Brother International LK3-B431 MKII Instruction Manual - Page 16

Installing, motor, pulley

Get Brother International LK3-B431 MKII PDF manuals and user guides View all Brother International LK3-B431 MKII manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

3. INSTALLATION 3-2 . Installing the motor O 0 e43 Install the motor 0 to the work table with the four accessory bolts 0, cushions 0, cushion collars 0, flat washers 0, spring washers 0 and nuts G. At that time, fix by setting bolts 0 a little to the right of oval hole on motor. NOTE: Tighten the nuts 0 so that the clearance between the table and the cushion collars 0 is approximately 1 mm. Table 1mm 3-3 . Installing the motor pulley C> 9 Place the motor pulley 0 onto the shaft of the motor 0 so that the key groove is aligned, and then tighten the set screw so that the center of the V groove in the motor pulley 0 is aligned as closely as possible with the center of the belt hole in the power table. 9 LK3-8430E-, B431E-, B432E-, B433E- Mark II

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
3.
INSTALLATION
3-2
.
Installing
the
motor
1mm
O
0
e43
Table
3-3
.
Installing
the
motor
pulley
C>
Install
the
motor
0
to
the
work
table
with
the
four
ac-
cessory
bolts
0,
cushions
0,
cushion
collars
0,
flat
washers
0,
spring
washers
0
and
nuts
G.
At
that
time,
fix
by
setting
bolts
0
a
little
to
the
right
of
oval
hole
on
motor.
NOTE:
Tighten
the
nuts
0
so
that
the
clearance
between
the
table
and
the
cushion
collars
0
is
approximately
1
mm.
Place
the
motor
pulley
0
onto
the
shaft
of
the
motor
0
so
that
the
key
groove
is
aligned,
and
then
tighten
the
set
screw
so
that
the
center
of
the
V
groove
in
the
motor
pulley
0
is
aligned
as
closely
as
possible
with
the
center
of
the
belt
hole
in
the
power
table.
9
LK3-8430E-,
B431
E-,
B432E-,
B433E-
Mark
II