Brother International LK3-B431 MKII Instruction Manual - Page 51

Changing, Functions, Using, Switches

Get Brother International LK3-B431 MKII PDF manuals and user guides View all Brother International LK3-B431 MKII manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

12 . CHANGING FUNCTIONS USING THE DIP SWITCHES 12. CHANGING FUNCTIONS USING THE DIP SWITCHES 12-1. Operation panel DIP switches The operation panel DIP switches 0 are used to change functions which might need to be changed depending on the sewing conditions. NOTE: Always turn off the power before setting the DIP switches. The functions shown in the table below can be changed by means of these DIP switches. * All DIP switches are set to OFF at the time of ship- ment. OFF ON Switch DIPA-1 DIPA-2 DIPA-3 DIPA-4 DIPA-5 DIPA-6 DIPA-7 DIPA-8 Motion when set to ON Presser does not automatically lift after sewing is completed. Two-pedal mode is available. See "12-2. Setting the presser mode" User program mode is available. - The presser does not rise automatically when a split is found. Displays the enlargement/reduction ratio in millimeter units instead of as a percentage. (After changing this setting, be sure to carry out the auto-clear operation by referring to page 41.) Enlargement of pattern size is not available. Program number is fixed. 12-2. Setting the presser mode Through the combination of DIP switches A-1 and A-2 on the operation panel, presser motions can be set as follows: DIPA-1 - ON - ON DIPA-2 - ON ON Pedal specifications Single pedal Single pedal Raising the presser at the sewing end Presser is raised automatically. Presser is raised by pressing the pedal. Two pedals Presser is raised automatically, then it is lowered by pressing the pedal. Two pedals Presser is kept lifted while the pedal is pressed. LK3-B430E-, 8431E-, B432E-, B433E- Mark II 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
12
.
CHANGING
FUNCTIONS
USING
THE
DIP
SWITCHES
12.
CHANGING
FUNCTIONS
USING
THE
DIP
SWITCHES
12-1.
Operation
panel
DIP
switches
The
operation
panel
DIP
switches
0
are
used
to
change
functions
which
might
need
to
be
changed
depending
on
the
sewing
conditions.
NOTE:
Always
turn
off
the
power
before
setting
the
DIP
switches.
The
functions
shown
in
the
table
below
can
be
changed
by
means
of
these
DIP
switches.
*
All
DIP
switches
are
set
to
OFF
at
the
time
of
ship-
ment.
O
FF
ON
Switch
Motion
when
set
to
ON
DIPA-1
Presser
does
not
automatically
lift
after
sewing
is
completed.
See
"12-2.
Setting
the
presser
mode"
DIPA-2
Two
-pedal
mode
is
available.
DIPA-3
User
program
mode
is
available.
DIPA-4
-
DIPA-5
The
presser
does
not
rise
automatically
when
a
split
is
found.
DIPA-6
Displays
the
enlargement/reduction
ratio
in
millimeter
units
instead
of
as
a
percentage.
(After
changing
this
setting,
be
sure
to
carry
out
the
auto
-clear
operation
by
referring
to
page
41.)
DIPA-7
Enlargement
of
pattern
size
is
not
available.
DIPA-8
Program
number
is
fixed.
12-2.
Setting
the
presser
mode
Through
the
combination
of
DIP
switches
A-1
and
A-2
on
the
operation
panel,
presser
motions
can
be
set
as
follows:
DIPA-1
DIPA-2
Pedal
specifications
Raising
the
presser
at
the
sewing
end
—
—
Single
pedal
Presser
is
raised
automatically.
ON
Single
pedal
Presser
is
raised
by
pressing
the
pedal.
—
ON
Two
pedals
Presser
is
raised
automatically,
then
it
is
lowered
by
pressing
the
pedal.
ON
ON
Two
pedals
Presser
is
kept
lifted
while
the
pedal
is
pressed.
LK3-B430E-,
8431
E-,
B432E-,
B433E-
Mark
II
44