Canon FAX-JX210P User's Guide - Page 76

Chk Printer B200 / Require Service, Chk Printer Nnnn / See Manual, Clear Paper Jam, Doc. Too Long, - fax service manual

Get Canon FAX-JX210P PDF manuals and user guides View all Canon FAX-JX210P manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

„ CHK PRINTER B200 / REQUIRE SERVICE Cause Action An error requiring servicing might have occurred. If using the machine as phone, contact the service center, then turn off the machine immediately. If not using as phone, turn off the machine immediately, then contact the service center using your phone. „ CHK PRINTER nnnn / SEE MANUAL Cause Action An error requiring servicing might have Turn off the machine, and unplug the power cord of the machine from the power occurred. supply. After a while, plug the power cord of the machine back in and turn on the machine. If the same error occurs, contact the service center. „ CLEAR PAPER JAM Cause There is a paper jam. „ DOC. TOO LONG Action Clear the paper jam (see page 60) and reload paper in the Rear Tray. Press [Stop/Reset]. Cause The document is longer than 15.8 in. (400 mm). „ ECM RX Action Use a copier to make a reduced copy of the document and then send the copy. Cause The fax is receiving a document using Error Correction Mode (ECM). „ ECM TX Action ECM receptions may take longer than normal receptions. Turn off ECM if you need to receive quickly, or if you know your local lines are in good condition (see on page 46). Cause The fax is sending a document using Error Correction Mode (ECM). „ INK ABS NEAR FUL Action ECM transmissions may take longer than normal transmissions. Turn off ECM if you need to transmit quickly, or if you know your local lines are in good condition (see on page 46). Cause The ink absorber is almost full. „ INK VOL UNKNOWN Action Printing will no longer be possible once the ink absorber is full. Contact the service center immediately. Press [Stop/Reset] to continue printing. Cause The remaining level of the ink cannot be correctly detected. Action A FINE Cartridge that was once empty is installed. Replace the FINE Cartridge (see page 50). Troubleshooting 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
75
Troubleshooting
CHK PRINTER B200 / REQUIRE SERVICE
CHK PRINTER nnnn / SEE MANUAL
CLEAR PAPER JAM
DOC. TOO LONG
ECM RX
ECM TX
INK ABS NEAR FUL
INK VOL UNKNOWN
Cause
Action
An error requiring servicing might have
occurred.
If using the machine as phone, contact the service center, then turn off the
machine immediately.
If not using as phone, turn off the machine immediately, then contact the service
center using your phone.
Cause
Action
An error requiring servicing might have
occurred.
Turn off the machine, and unplug the power cord of the machine from the power
supply. After a while, plug the power cord of the machine back in and turn on the
machine. If the same error occurs, contact the service center.
Cause
Action
There is a paper jam.
Clear the paper jam (see page 60) and reload paper in the Rear Tray. Press
[Stop/Reset].
Cause
Action
The document is longer than 15.8 in.
(400 mm).
Use a copier to make a reduced copy of the document and then send the copy.
Cause
Action
The fax is receiving a document using
Error Correction Mode (ECM).
ECM receptions may take longer than normal receptions. Turn off ECM if you
need to receive quickly, or if you know your local lines are in good condition (see
<ECM RX> on page 46).
Cause
Action
The fax is sending a document using
Error Correction Mode (ECM).
ECM transmissions may take longer than normal transmissions. Turn off ECM if
you need to transmit quickly, or if you know your local lines are in good condition
(see <ECM TX> on page 46).
Cause
Action
The ink absorber is almost full.
Printing will no longer be possible once the ink absorber is full. Contact the
service center immediately. Press [Stop/Reset] to continue printing.
Cause
Action
The remaining level of the ink cannot
be correctly detected.
A FINE Cartridge that was once empty is installed. Replace the FINE Cartridge
(see page 50).