Canon PIXMA MX892 Guide for Printer Setup for Network
Canon PIXMA MX892 Manual
The manual viewer requires the flash plugin to be installed and enabled.
To view this page ensure that Adobe Flash Player version 10 or greater is installed.
Canon PIXMA MX892 manual table of contents:
-
Page 1
Setup Guide This guide provides information for setting up a network connection for the printer. Network Connection Wireless Connection Preparation for Connection ... setup) Disable WEP WPA/WPA2 Wired Connection Preparation for Connection Cable Connection Printer Setup Character Entry Troubleshooting -
Page 2
... settings of the network device vary depending on your system environment. For details, refer to the manual of your network device or contact its manufacturer. • Check if your device supports IEEE802.11n, 802.11g or 802.11b. • If your device is set ... -
Page 3
... enabled. c Setup Procedure Selection The printer will automatically search for access points supporting WPS (Wi-Fi Protected Setup). If the Push Button Method... printer but you are unsure if your access point or router supports this technology, press the Stop button and choose Standard setup. Push ... -
Page 4
...WPS 1. Press and hold the WPS button on the access point (for about 5 seconds). For details on pressing the WPS button, refer to the access point manual. 2. Press the OK button on the printer within 2 minutes. The (blue) Wi-Fi lamp on the printer flashes while searching for or connecting to the ... -
Page 5
d-B Standard setup d Connection via Standard setup 1. Select Standard setup. 2. Press the OK button. 3. Select your access point, then press the OK button. 4. One of the screens above will be displayed on the printer. 5. Press the OK button. 6. Enter the network password (WEP key or passphrase)... -
Page 6
.... 6. Press and hold the WPS button on the access point (for about 5 seconds). For details on pressing the WPS button, refer to the access point manual. 7. Press the OK button on the printer within 2 minutes. The (blue) Wi-Fi lamp on the printer flashes while searching for or connecting to the ... -
Page 7
d-D Other setup (Advanced setup) d Connection via Advanced setup 1. Select Other setup. 2. Press the OK button. 3. Select Advanced setup. 4. Press the OK button. 5. Select your access point, then press the OK button. 6. Select a security protocol for the access point, then press the OK button.... -
Page 8
9. Press the OK button. 10.Enter the WEP key of your access point or router. 11. Press the left Function button. 12.Make sure that the WEP key is correct. 13.Press the left Function button. 14.When the left screen appears, press the OK button. The network connection setup is now complete. ... -
Page 9
12.When the left screen appears, press the OK button. The network connection setup is now complete. -
Page 10
...configuration, router functions, setup procedures and security settings of the network device vary depending on your system environment. For details, refer to the manual of your network device or contact its manufacturer. • For office use, consult your network administrator. • Take added care ... -
Page 11
c Printer Setup 1. Press the MENU button (A) on the printer. 2. Use the buttons (A) to select the Setup icon. 3. Press the OK button (B). 4. Select Device settings. 5. Press the OK button. 6. Select LAN settings. 7. Press the OK button. 8. Select Change wireless/wired. 9. Press the OK button... -
Page 12
12. Press the MENU button. The network connection setup is now complete. -
Page 13
.... Follow the procedure below. 1. When an on-screen keyboard shown above is displayed, press the center Function button (A) to switch to a keyboard that supports characters you want to use. Three types of keyboard (upper case alphabetical, lower case alphabetical and numeric/symbolic) are available.... -
Page 14
Troubleshooting Standard setup The Target Access Point is Not Detected Check the access point name/network name and ...configure wireless connection settings again. "WPA/WPA2 Enterprise" is not supported on this printer. For details on how to change the security protocol (encryption standard) for ... -
Page 15
.... Make sure that the passphrase entered for the access point is correct. If the problem is not resolved, there may be other causes. See also the .... For details on how to check or change the settings of the access point, refer to the manual supplied with the access point or contact its manufacturer. -
Page 16
...> WLAN setting list to check MAC address. For details on how to change the settings of the access point, refer to the manual supplied with the access point or contact its manufacturer. If the problem is not resolved, there may be other causes. See also the... -
Page 17
...LAN settings > Confirm LAN settings > WLAN setting list to check MAC address. For details on how to change the settings of the access point, refer to the manual supplied with the access point or contact its manufacturer. To perform Standard setup again 1. Press the MENU button (A). 2. Use the ... -
Page 18
... button on only one access point. Connection failed. See the manual. The screen appears when an error occurs. Check the access point ... again. For details on how to check the settings of the access point, refer to the manual supplied with the access point or contact its manufacturer. Timeout ... -
Page 19
... (A) on the printer to search for the access point again. If the problem is not resolved, there may be other causes. See also ...¬gure wireless connection settings again. "WPA/WPA2 Enterprise" is not supported on this printer. For details on how to change the security protocol (encryption standard) ... -
Page 20
... of the access point, refer to the manual supplied with the access point or contact its manufacturer. If the problem is not resolved, there may ... contact its manufacturer. The Passphrase is Not Displayed Automatically Refer to the manual supplied with the access point or contact its manufacturer. -
Page 21
... of the access point, refer to the manual supplied with the access point or contact its manufacturer. If the problem is not resolved, there .... For details on how to change the settings of the access point, refer to the manual supplied with the access point or contact its manufacturer. Select Directly... -
Page 22
...on how to check or change the settings of the access point, refer to the manual supplied with the access point or contact its manufacturer. To specify ...IP address, then press the OK button. 10. Select Manual setup, then press the OK button. Follow the on-screen instructions to proceed with settings. ...