Craftsman 21194 Operation Manual - Page 17

Warning

Get Craftsman 21194 - 7-1/4 in. Sliding Compound Miter Saw PDF manuals and user guides View all Craftsman 21194 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

i,A WARNING ] To avoid injury, do not connect this miter saw to the power source until it is completely assembled and adjusted, and you have read and understood this Operator's Manual. iNSTALLING THE MITER HANDLE (FIG. A) 1. Thread the miter handle (1) into the hole located at the front of the miter table. Fig. A To empty the dust bag, squeeze the metal collar and remove from exhaust port. Open zipper on underside of bag and empty into waste container. NOTE: Check frequently and empty bag before it gets full. iNSTALLING THE SAFETY HOLDDOWN CLAMP (FIG. C) 1. Loosen the hex screw (3) using a Phillips screwdriver from the rear side of the saw base. 2. Place the hold-down clamp assembly (1) in one of the mounting holes (2). 3. Tighten the hex screw (3). FigC. iNSTALLING THE DUST BAG (FIG. B) 1. Squeeze the metal collar wings of the dust bag (1). 2. Place the dust bag neck opening around the exhaust port (2), and release the metal collar wings. 2 31 2C:: _Z_\:: JK \_ SAW BLADE WRENCH (FIG. D) For convenient storage and prevention of loss, there is a slot (1) in the right side of the switch handle (2) for storing the blade wrench (3) when not in use. /, Fig.2 D_I 3 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
i,A
WARNING
]
To avoid injury, do not connect
this
miter
saw
to the
power source
until
it is completely
assembled
and
adjusted,
and
you have read and
understood
this
Operator's
Manual.
iNSTALLING
THE MITER
HANDLE
(FIG. A)
1. Thread the miter handle (1)
into
the
hole located at the front of the miter
table.
Fig. A
iNSTALLING
THE DUST BAG (FIG. B)
1. Squeeze the metal collar wings of the
dust bag (1).
2. Place the dust bag neck opening
around the exhaust port (2), and
release the metal collar wings.
To empty the dust bag, squeeze the
metal collar and remove from exhaust
port. Open zipper on underside of bag
and empty
into waste container.
NOTE:
Check frequently
and empty
bag before it gets full.
iNSTALLING
THE SAFETY
HOLD-
DOWN CLAMP
(FIG. C)
1.
Loosen the hex screw (3) using a
Phillips screwdriver
from the rear
side of the saw base.
2.
Place the hold-down clamp
assembly
(1) in one of the mounting
holes (2).
3. Tighten
the hex screw
(3).
Fig.
C
2C::
_Z_\::
J
K
\_
3
1
SAW BLADE
WRENCH
(FIG. D)
2
For convenient
storage and prevention
of loss, there
is
a slot (1)
in
the right
side of the switch handle (2) for storing
the blade wrench (3) when not in use.
/,
Fig.2D_I
3
17