Cub Cadet CC 600 Operation Manual - Page 12
Service - oil change
View all Cub Cadet CC 600 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
Service Maintenance WARNING! Before performing any maintenance or repairs, disengage blades, stop engine and remove key (if equipped) to prevent unintended starting. General Recommendations • Always observe safety rules when performing any maintenance. • The warranty on this lawn mower does not cover items that have been subjected to operator abuse or negligence. To receive full value from warranty, operator must maintain the lawn mower as instructed here. • Changing of engine-governed speed will void engine warranty. • All adjustments should be checked at least once each season. • Periodically check all fasteners and make sure these are tight. WARNING: Always stop engine, allow engine to cool, disconnect spark plug, and ground against engine before performing any type of maintenance on your machine. Lubrication WARNING! Before lubricating, repairing, or inspecting, always disengage blades , stop engine and remove key (if equipped) to prevent unintended starting. 1. Lubricate pivot points on the blade and drive controls at least once a season with light oil. These controls must operate freely in both directions. See Figure 4-1. Figure 4-1 2. The transmission is pre-lubricated and sealed at the factory and does not require lubrication. 3. Follow the accompanying Engine Operator's Manual for lubrication schedule and instruction for engine lubrication. 12 Front Caster Wheels (If Equipped) Each of the front wheel axles and casters is equipped with a grease fitting. See Figure 4-3. Lubricate with a No. 2 multi-purpose grease applied with a grease gun after every 25 hours of mower operation or once a season. Figure 4-2 Engine A list of key engine maintenance jobs required for good performance by the mower is given below. Follow the Engine Operator's Manual for a detailed list of maintenance intervals and instructions. • Maintain oil level as instructed in the Engine Operator's Manual. • Service air cleaner once a season under normal conditions. Clean every few hours under extremely dusty conditions. Poor engine performance and flooding usually indicates that the air cleaner should be serviced. To service the air cleaner, refer to the engine manual. • Clean spark plug and reset the gap once a season. Spark plug replacement is recommended at the start of each mowing season. Check Engine Operator's Manual for correct plug type and gap specifications. • Clean engine regularly with a cloth or brush. Keep the top of the engine clean to permit proper air circulation. Remove all grass, dirt, and combustible debris from muffler area. • Engines stored between 30 and 90 days need to be treated with a gasoline stabilizer to prevent deterioration and gum from forming in fuel system or on essential carburetor parts. Changing the Engine Oil WARNING! If the engine has been recently run, the engine, muffler and surrounding metal surfaces will be hot and can cause burns to the skin. Exercise caution to avoid burns. 4 Refer to the Engine Operator's Manual for specific oil change intervals. 1. Pull up the oil drain hose to release it from the deck. See Figure 4-3 for MTD engine and Figure 4-4 for Briggs & Stratton engine. NOTE: The engine is equipped with either a plastic twist-off or metal square head cap. Refer to Figure 4-3 insets. 3 3 Figure 4-3 NOTE: For units equipped with the Briggs & Stratton engine and bagger, remove the bagger from the mower, which will expose a hole in the back plate of the mower when the bagger door closes to pass the oil drain hose through. See Figure 4-4. Hole Oil Drain Hose Cap Figure 4-4 2. Position the end of the hose over an appropriate oil collection container with at least a 20 ounce capacity, to collect the used oil. NOTE: On units with the Briggs & Stratton engine and rear draining oil hose, tip the mower back to help drain the oil from the engine. 3. Unscrew the cap on the end of the oil drain hose to begin draining oil. See Figure 4-3 inset. 4. After the oil has finished draining, screw the cap back onto the end of the oil drain hose. See Figure 4-5.