D-Link DCS-3220G Product Manual - Page 128

Reset and Restore

Get D-Link DCS-3220G - SECURICAM Network Camera PDF manuals and user guides
UPC - 790069269523
View all D-Link DCS-3220G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 128 highlights

Reset and Restore There is a button hidden in the pinhole beside the Ethernet socket. It is used to reset the system or restore the factory default settings. Sometimes resetting the DCS-3220G will return the system back to a normal state. If the system still has problems after reset, restore the factory settings and install again: RESET: 1. Lightly insert a paper clip (or a similar sized tool) into the reset hole on the back of the camera, press lightly and then release the button. 2. The LED on the front of the camera will begin blinking red and green fast. 3. When the LED stops the blinking fast and starts blinking once every second, the reset is completed. RESTORE: 1. Insert the paper clip, or another similar tool, and press and continuously hold down the button recessed inside the reset hole. 2. Wait for the LED on the front of the camera to blink red and green and hold the button through two cycles of blinking (about 5-7 seconds.) 3. Withdraw the tool after the second cycle of the LED blinking and a factory restore has been completed. Reset button Restoring the factory defaults will result in the loss of any previous settings and will require running the IP Installer to find the camera's IP address. 128

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
128
There is a button hidden in the pinhole beside the Ethernet socket. It is
used to
reset
the system or
restore
the factory default settings.
Sometimes resetting the
DCS-3220G
will return the system back to a
normal state. If the system still has problems after reset, restore the
factory settings and install again:
RESET
:
1. Lightly insert a paper clip (or a similar sized tool) into the
reset hole on the back of the camera, press lightly and
then release the button.
2. The LED on the front of the camera will begin blinking red
and green fast.
3. When the LED stops the blinking fast and starts blinking
once every second, the reset is completed.
RESTORE
:
1. Insert the paper clip, or another similar tool, and press
and continuously hold down the button
recessed inside
the reset hole.
2. Wait for the LED on the front of the camera to blink red
and green and hold the button through two cycles of
blinking (about 5-7 seconds.)
3. Withdraw the tool after the second cycle of the LED
blinking and a factory restore has been completed.
Reset and Restore
Restoring the factory defaults will result in the
loss of any previous settings and will require
running the
IP Installer
to find the camera’s IP
address.
Reset button