Home » D-Link Manuals » Hubs & Switches » D-Link DES-3852 » Manual Viewer

D-Link DES-3852 Product Manual - Page 121

enable pvid auto_assign, Purpose, Syntax, Description, Parameters, Restrictions

UPC - 790069289460

Add to My Manuals
Save this manual to your list of manuals

Page 121 highlights

xStack DES-3800 Series Layer 3 Stackable Fast Ethernet Managed Switch CLI Manual enable pvid auto_assign Purpose Syntax Description Used to enable auto assignment of pvid enable pvid auto_assign The command enables the auto-assign of PVID. If "Auto-assign PVID" is enabled, the PVID will possibly be changed by the PVID or VLAN configuration. When a user configures a port to VLAN X's be untagged membership, this port's PVID will be updated with VLAN X. In the form of VLAN list command, PVID is updated with last item of VLAN list. When a user removes a port from the untagged membership of the PVID's VLAN, the port's PVID will be assigned with "default VLAN". Parameters Restrictions None. Only Administrator or Operator-level users can issue this command. Example usage: To enable the enable the auto assignment of pvid: DES-3800:admin#enable pvid auto_assign Command: enable pvid auto_assign Success. DES-3800:admin# disable pvid auto_assign Purpose Syntax Description Parameters Restrictions Used to disable auto assignment of pvid disable pvid auto_assign This command disables auto-assign of pvid. If "auto-assign PVID" is disabled, PVID only be changed by PVID configuration (user changes explicitly). The VLAN configuration will not automatically change PVID. None. Only Administrator or Operator-level users can issue this command. Example usage: To enable the enable the auto assignment of pvid: DES-3800:admin#disable pvid auto_assign Command: disable pvid auto_assign Success. DES-3800:admin# 117

Section	Page
INTRODUCTION	5
Using the Console CLI	7
Command Syntax	11
Basic Switch Commands	13
Switch Port Commands	31
SNMP V3	35
PoE Commands	49
Network Management Commands	54
Switch Utility Commands	62
Network Monitoring Commands	73
Layer 2 FDB Commands	86
Packet Storm Control Commands	94
QoS Commands	98
Mirror Configuration Commands	106
VLAN Commands	109
Link Aggregation Commands	123
IGMP Snooping Commands	127
802.1X Commands (Including Guest VLANs)	135
Access Control List (ACL) Commands	148
Traffic Segmentation Commands	168
Command List History	170
Basic IP Commands (For Layer 3)	173
ARP Commands	178
Routing Table Commands	182
Route Redistribution Commands	185
RIP Commands	191
IGMP Commands	195
Auto Config Commands V3	199
DNS Relay Commands	201
DVMRP Commands	205
IP Multicasting Commands	210
MD5 Commands	213
OSPF Configuration Commands	215
Time and SNTP Commands	232
Port Security Commands	238
MAC Notification Commands	242
SSH Commands	246
Jumbo Frame Commands	254
Access Authentication Control Commands	256
D-Link Single IP Management Commands	279
Multiple Spanning Tree Protocol (MSTP) Commands	289
SSL Commands	301
VRRP Commands	307
System Severity	316
DHCP Relay	318
IP-MAC Binding Commands	324
LACP Configuration Commands	338
CPU Interface Filtering (Software ACL) Commands	340
Modify Prompt and Banner Commands	348
Safeguard Engine	351
WRED Command List	353
Web-based Access Control (WAC) Commands	357
Double VLAN Command List	363
Limited Multicast IP Address Commands	368
Route Preference Commands	373
MAC-Based Access Control Commands	376
PIM Commands	385
Loopback Interface Commands	402
DHCP Server Command List	405
MLD Snooping Commands	421
Loopback Detection Commands	428
Password Recovery Commands	433
Multicast VLAN Commands	436
CPU Filtering Commands List	439
Broadcast Segmentation Commands	441
Technical Specifications	443