Dell Alienware m15 R3 Service Manual - Page 29

Display assembly, Removing the display assembly

Get Dell Alienware m15 R3 PDF manuals and user guides View all Dell Alienware m15 R3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Steps 1. Push the rear I/O-cover into the palm-rest assembly snapping it into place. NOTE: To avoiding damaging your computer, ensure the Tron light cable is not pinched and that the Mylar is pasted on the system board before snapping the rear I/O-cover into place. 2. Replace the two screws (M2.5x4) that secure the rear I/O-cover to the palm-rest assembly. 3. Replace the two screws (M2.5x5) that secure the rear I/O-cover to the palm-rest assembly. 4. Peel and lift the Mylar from the system board. 5. Connect the Tron light cable to the system board. 6. Route and adhere the Tron light cable into place on the system board. 7. Adhere the Mylar into place onto the system board. Next steps 1. Install the base cover. 2. Follow the procedure in After working inside your computer. Display assembly Removing the display assembly Prerequisites 1. Follow the procedure in Before working inside your computer. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Steps
1.
Push the rear I/O-cover into the palm-rest assembly snapping it into place.
NOTE: To avoiding damaging your computer, ensure the Tron light cable is not pinched and that the Mylar is pasted on
the system board before snapping the rear I/O-cover into place.
2.
Replace the two screws (M2.5x4) that secure the rear I/O-cover to the palm-rest assembly.
3.
Replace the two screws (M2.5x5) that secure the rear I/O-cover to the palm-rest assembly.
4.
Peel and lift the Mylar from the system board.
5.
Connect the Tron light cable to the system board.
6.
Route and adhere the Tron light cable into place on the system board.
7.
Adhere the Mylar into place onto the system board.
Next steps
1.
Install the
base cover
.
2.
Follow the procedure in
After working inside your computer
.
Display assembly
Removing the display assembly
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
29