Dell Inspiron 3030 Small Desktop Owners Manual - Page 62

Antenna modules, Removing the antenna module

Get Dell Inspiron 3030 Small Desktop PDF manuals and user guides View all Dell Inspiron 3030 Small Desktop manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Figure 43. Routing the cables through the routing guides Steps 1. Align and slide the tabs on the power supply unit into the latches on the chassis. 2. Align the screw holes on the power supply unit with the screw holes on the chassis. 3. In a sequential order (1>2>3), replace the three screws (#6-32) to secure the power supply unit on the chassis. 4. Route the power supply unit cables through the routing guides on the chassis. 5. Connect the system-board power cable and the processor-power cable to the connectors on the system board. Next steps 1. Install the hard-drive and optical-drive cage. 2. Install the 3.5-inch hard drive. 3. Install the front cover. 4. Install the left-side cover. 5. Follow the procedure in After working inside your computer. Antenna modules Removing the antenna module CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the left-side cover. 62 Removing and installing Field Replaceable Units (FRUs)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Figure 43. Routing the cables through the routing guides
Steps
1.
Align and slide the tabs on the power supply unit into the latches on the chassis.
2.
Align the screw holes on the power supply unit with the screw holes on the chassis.
3.
In a sequential order (1>2>3), replace the three screws (#6-32) to secure the power supply unit on the chassis.
4.
Route the power supply unit cables through the routing guides on the chassis.
5.
Connect the system-board power cable and the processor-power cable to the connectors on the system board.
Next steps
1.
Install the
hard-drive and optical-drive cage
.
2.
Install the
3.5-inch hard drive
.
3.
Install the
front cover
.
4.
Install the
left-side cover
.
5.
Follow the procedure in
After working inside your computer
.
Antenna modules
Removing the antenna module
CAUTION:
The information in this section is intended for authorized service technicians only.
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
left-side cover
.
62
Removing and installing Field Replaceable Units (FRUs)