Dell Inspiron 3030 Small Desktop Owners Manual - Page 70

System board, Removing the system board

Get Dell Inspiron 3030 Small Desktop PDF manuals and user guides View all Dell Inspiron 3030 Small Desktop manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Figure 51. Installing the processor Steps 1. Extend the release lever and the processor cover completely in an open position. NOTE: The side of the fan with the word 'REAR' written must face the rear of the chassis. NOTE: The stubs on the fan shroud must align to the corresponding stub holes on the processor fan. 2. Align the notches on the processor with the tabs on the processor socket. 3. Place the processor in the processor socket. 4. Close the processor cover. 5. Pivot the release lever down and place it under the tab on the processor socket. Next steps 1. Install the processor fan and heat-sink assembly. 2. Install the fan shroud. 3. Install the left-side cover. 4. Follow the procedure in After working inside your computer. System board Removing the system board CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the left-side cover. 3. Remove the front cover. 4. Remove the 3.5-inch hard drive. 5. Remove the hard-drive and optical-drive cage. 6. Remove the memory. 7. Remove the M.2 2230 solid-state drive or the M.2 2280 solid-state drive, whichever is applicable. 70 Removing and installing Field Replaceable Units (FRUs)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Figure 51. Installing the processor
Steps
1.
Extend the release lever and the processor cover completely in an open position.
NOTE:
The side of the fan with the word 'REAR' written must face the rear of the chassis.
NOTE:
The stubs on the fan shroud must align to the corresponding stub holes on the processor fan.
2.
Align the notches on the processor with the tabs on the processor socket.
3.
Place the processor in the processor socket.
4.
Close the processor cover.
5.
Pivot the release lever down and place it under the tab on the processor socket.
Next steps
1.
Install the
processor fan and heat-sink assembly
.
2.
Install the
fan shroud
.
3.
Install the
left-side cover
.
4.
Follow the procedure in
After working inside your computer
.
System board
Removing the system board
CAUTION:
The information in this section is intended for authorized service technicians only.
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
left-side cover
.
3.
Remove the
front cover
.
4.
Remove the
3.5-inch hard drive
.
5.
Remove the
hard-drive and optical-drive cage
.
6.
Remove the
memory
.
7.
Remove the
M.2 2230 solid-state drive
or the
M.2 2280 solid-state drive
, whichever is applicable.
70
Removing and installing Field Replaceable Units (FRUs)