Dell Latitude 7220 Rugged Extreme Tablet Service Manual - Page 61

Installing the docking board

Get Dell Latitude 7220 Rugged Extreme Tablet PDF manuals and user guides View all Dell Latitude 7220 Rugged Extreme Tablet manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Installing the docking board Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the docking board and provides a visual representation of the installation procedure. Steps 1. Connect the docking board cable to the connector. NOTE: Slide the cable through the connector clips, and release the latch. 2. Align the docking board and replace the five (M2x5) screws that secure the docking board to the system chassis. 3. Replace the adhesive tape to secure the docking board to the system chassis. Next steps 1. Install the system board. 2. Install the coin-cell battery. 3. Install the front camera. 4. Install the microphone. 5. Install the WWAN. 6. Install the WLAN. 7. Install the solid-state drive. 8. Install the system fan. 9. Install the heat-sink. 10. Install the display assembly. 11. Install the batteries. 12. Follow the procedure in after working inside your tablet. Removing and installing components 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
Installing the docking board
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the docking board and provides a visual representation of the installation procedure.
Steps
1.
Connect the docking board cable to the connector.
NOTE:
Slide the cable through the connector clips, and release the latch.
2.
Align the docking board and replace the five (M2x5) screws that secure the docking board to the system chassis.
3.
Replace the adhesive tape to secure the docking board to the system chassis.
Next steps
1.
Install the
system board
.
2.
Install the
coin-cell battery
.
3.
Install the
front camera
.
4.
Install the
microphone
.
5.
Install the
WWAN
.
6.
Install the
WLAN
.
7.
Install the
solid-state drive
.
8.
Install the
system fan
.
9.
Install the
heat-sink
.
10.
Install the
display assembly
.
11.
Install the
batteries
.
12.
Follow the procedure in
after working inside your tablet
.
Removing and installing components
61