Dell PowerConnect 2708 User's Guide - Page 30

Installing the Device on a Flat Surface, Bracket Installation for Wall Mounting

Get Dell PowerConnect 2708 PDF manuals and user guides View all Dell PowerConnect 2708 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Installing the Device on a Flat Surface The device can be installed on a flat surface, such as a desk-top, if it is not installed on a rack or on a wall. The surface must be able to support the weight of the device and the device cables. 1 Attach the self-adhesive rubber pads (provided with the device) on each marked location on the bottom of the chassis. 2 Set the device on a flat surface, while leaving 5.08 cm (2 inches) on each side, and 12.7 cm (5 inches) at the back. 3 Ensure that the device has proper ventilation. Installing the Device on a Wall 1 Place the supplied wall-mounting bracket on one side of the device, ensuring that the mounting holes on the device line up to the mounting holes on the rack-mounting bracket. The following figure illustrates where to mount the brackets. Figure 3-3. Bracket Installation for Wall Mounting 2 Insert the supplied screws into the rack-mounting holes and tighten with a screwdriver. 3 Repeat the process for the wall-mounting bracket on the other side of the device. 4 Place the device on the wall in the location where the device is being installed. 5 On the wall mark the locations where the screws to hold the device must be prepared. 6 On the marked locations, drill the holes and place all plugs (not provided) in the holes. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
30
Installing the Device on a Flat Surface
The device can be installed on a flat surface, such as a desk-top, if it is not installed on a rack or on
a wall. The surface must be able to support the weight of the device and the device cables.
1
Attach the self-adhesive rubber pads (provided with the device) on each marked location on
the bottom of the chassis.
2
Set the device on a flat surface, while leaving 5.08 cm (2 inches) on each side, and 12.7 cm (5
inches) at the back.
3
Ensure that the device has proper ventilation.
Installing the Device on a Wall
1
Place the supplied wall-mounting bracket on one side of the device, ensuring that the
mounting holes on the device line up to the mounting holes on the rack-mounting bracket.
The following figure illustrates where to mount the brackets.
Figure 3-3.
Bracket Installation for Wall Mounting
2
Insert the supplied screws into the rack-mounting holes and tighten with a screwdriver.
3
Repeat the process for the wall-mounting bracket on the other side of the device.
4
Place the device on the wall in the location where the device is being installed.
5
On the wall mark the locations where the screws to hold the device must be prepared.
6
On the marked locations, drill the holes and place all plugs (not provided) in the holes.