Edimax IC-3005 Manual - Page 104

V: Appendix

Get Edimax IC-3005 PDF manuals and user guides View all Edimax IC-3005 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

Chapter V: Appendix 5.1 Troubleshooting If the IP camera is not working properly, before you contact the dealer of purchase for help, please check the troubleshooting list here, this may help you to solve the problem by yourself and therefore saves your valuable time. Scenario I can not connect to IP camera Possible Solution a. Please confirm the IP address setting of the computer you‟re using. If they‟re not in the same subnet, they will not be able to communicate with each other. b. Please make the IP address you used to connect to the IP camera is correct. c. If you forget the IP address of the IP camera, you will have to reset it to factory default value (which is 192.168.2.3) by pressing „reset‟ button at the bottom of the IP camera. You‟ll need a pen or pin to be able to press the reset button. Press and hold reset button for 5 seconds, then try to connect to the IP camera with IP address „192.168.2.3‟ again. d. Please make sure IP camera is correctly powered (the „Power‟ LED should be on). e. If you‟re trying to connect to the IP camera from Internet, please make sure the port that IP camera uses (Video and HTTP port, see section 2.3.1) is not blocked by firewall or other software / hardware. Image refreshes very slow f. Contact dealer of purchase for help, if above solutions do not work. a. Try a higher frame rate setting, if it‟s not 30. b. Try a lower resolution. 104

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
104
Chapter V: Appendix
5.1 Troubleshooting
If the IP camera is not working properly, before you contact the dealer of
purchase for help, please check the troubleshooting list here, this may help
you to solve the problem by yourself and therefore saves your valuable time.
Scenario
Possible Solution
I can not connect to
IP camera
a. Please confirm the IP address setting of the
computer you
‟
re using. If they
‟
re not in the same
subnet, they will not be able to communicate with
each other.
b. Please make the IP address you used to connect to
the IP camera is correct.
c. If you forget the IP address of the IP camera, you
will have to reset it to factory default value (which is
192.168.2.3) by pressing
„
reset
‟
button at the bottom
of the IP camera. You
‟
ll need a pen or pin to be able
to press the reset button. Press and hold reset button
for 5 seconds, then try to connect to the IP camera
with IP address
„
192.168.2.3
‟
again.
d. Please make sure IP camera is correctly powered
(the
„
Power
‟
LED should be on).
e. If you
‟
re trying to connect to the IP camera from
Internet, please make sure the port that IP camera
uses (Video and HTTP port, see section 2.3.1) is not
blocked by firewall or other software / hardware.
f. Contact dealer of purchase for help, if above
solutions do not work.
Image refreshes
very slow
a. Try a higher frame rate setting, if it
‟
s not 30.
b. Try a lower resolution.