Edimax IC-3005 Manual - Page 105

on, but you still can not connect to the camera when

Get Edimax IC-3005 PDF manuals and user guides View all Edimax IC-3005 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

c. If you‟re connecting this camera from Internet, it could be caused by a slow Internet connection, and it‟s not a problem caused by camera. However, when the network connection is slow, you should use lower frame rate / resolution. d. Adjust the antenna if you‟re using wireless connection. The antenna should be perpendicular to the ground to get best reception, and the distance between IP camera and computer / wireless access point should not be too far. IP camera is not responding e. Try to adjust „MTU‟ setting if you‟re using PPPoE to connect to Internet. Ask your ISP or network administrator for detailed instruction. a. Is the network cable or wireless connection disconnected? Please check it. b. Unplug the power adapter from wall socket and plug it in again after 10 seconds, then try to connect to the IP camera again. Image is fuzzy c. If IP camera is correctly powered („Power‟ LED is on), but you still can not connect to the camera when you‟re sure that IP address is correct, please contact dealer of purchase for help). a. Use a soft cloth to clean the lens on the camera. You can use cloth with water, but DO NOT use alcohol or other chemical solution. b. Try to adjust brightness setting. c. If there‟s any light at the place where IP camera is located, switch it on and see if image looks better. I set the IP camera a. If the image is send by Email, please make sure it‟s 105

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
105
c. If you
‟
re connecting this camera from Internet, it
could be caused by a slow Internet connection, and
it
‟
s not a problem caused by camera. However, when
the network connection is slow, you should use lower
frame rate / resolution.
d. Adjust the antenna if you
‟
re using wireless
connection. The antenna should be perpendicular to
the ground to get best reception, and the distance
between IP camera and computer / wireless access
point should not be too far.
e. Try to adjust
„
MTU
‟
setting if you
‟
re using PPPoE to
connect to Internet. Ask your ISP or network
administrator for detailed instruction.
IP camera is not
responding
a. Is the network cable or wireless connection
disconnected? Please check it.
b. Unplug the power adapter from wall socket and
plug it in again after 10 seconds, then try to connect to
the IP camera again.
c. If IP came
ra is correctly powered („
Power
‟
LED is
on), but you still can not connect to the camera when
you
‟
re sure that IP address is correct, please contact
dealer of purchase for help).
Image is fuzzy
a. Use a soft cloth to clean the lens on the camera.
You can use cloth with water, but
DO NOT
use
alcohol or other chemical solution.
b. Try to adjust brightness setting.
c. If there
‟
s any light at the place where IP camera is
located, switch it on and see if image looks better.
I set the IP camera
a. If the image is send by Email, please make sure it
‟
s