Epson BrightLink 695Wi Installation Guide - Control Pad and Touch Unit - Page 17

bolt until the Touch Unit is parallel to the installation plate.

Get Epson BrightLink 695Wi PDF manuals and user guides View all Epson BrightLink 695Wi manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

5. Loosen the two M4 × 12 mm hexagon socket head cap bolts and adjust the position of the Touch Unit. Align the arrow on the left and right of the Touch Unit Bracket with the distance (f ) that you measured in step 4. Tighten the bolts with the supplied hexagon wrench when you have finished aligning the Touch Unit. 6. Insert the M4 × 55 mm or M4 × 70 mm hexagon socket head cap bolt into Touch Unit and tighten the bolt until the Touch Unit is parallel to the installation plate. The bolt used varies based on the distance from the wall to the surface of the whiteboard (f ) that you measured in step 4. If (f ) is 0.8 to 1.4 inches (20 to 35 mm), use the M4 × 55 mm bolt. If (f ) is 1.4 to 2.0 inches (35 to 50 mm), use the M4 × 70 mm bolt. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
16
5.
Loosen the two M4 × 12 mm hexagon socket head cap bolts and adjust the position of the Touch Unit.
Align the arrow on the left and right of the Touch Unit Bracket with the distance (f) that you measured
in step 4.
Tighten the bolts with the supplied hexagon wrench when you have finished aligning the Touch Unit.
6.
Insert the M4 × 55 mm or M4 × 70 mm hexagon socket head cap bolt into Touch Unit and tighten the
bolt until the Touch Unit is parallel to the installation plate.
The bolt used varies based on the distance from the wall to the surface of the whiteboard (f) that you
measured in step 4. If (f ) is 0.8 to 1.4 inches (20 to 35 mm), use the M4 × 55 mm bolt. If (f ) is 1.4 to
2.0 inches (35 to 50 mm), use the M4 × 70 mm bolt.