Epson BrightLink 695Wi Installation Guide - Control Pad and Touch Unit - Page 39

Touch Calibration

Get Epson BrightLink 695Wi PDF manuals and user guides View all Epson BrightLink 695Wi manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

When all of the dots have disappeared, press the button on the remote control and then go to step 15. If any dots remain (as shown below), do the following: • Remove any obstacles from around the projected screen. When you are finished, press the or button on the remote control and repeat step 12. • If the dots still remain after removing obstacles, select Additional Adjustments and follow the instructions. • If the dots still remain or there are obstacles that cannot be removed, such as whiteboard trays or frames, go to step 14. 14. If there is an obstacle that cannot be removed, such as a whiteboard tray or frame, remove the tape from the back of the supplied infrared deflectors and stick them to the screen so that the laser is not reflected by the obstacle. Make sure to stick the deflectors between the dots and the obstacle and use as many deflectors as necessary to match the width of the dots. ❏ Do not remove an infrared deflector once it has been stuck in place. ❏ Do not stick tape or place anything on the infrared deflectors. The deflectors will not function properly if anything is placed on them. After placing the infrared deflectors, press the or button on the remote control, and then repeat step 12. If the dots do not disappear even after attaching the infrared deflectors, select Additional Adjustments and follow the instructions. If the dots do not disappear even after performing the above procedures, contact Epson. 15. Perform touch calibration by pressing Menu on the remote control. On the Extended menu, select Easy Interactive Function, then Touch Unit Setup. Select Touch Calibration and follow the instructions. 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
38
When all of the dots have disappeared, press the
button on the remote control and then go to
step 15.
If any dots remain (as shown below), do the following:
•
Remove any obstacles from around the projected screen. When you are finished, press the
or
button on the remote control and repeat step 12.
•
If the dots still remain after removing obstacles, select
Additional Adjustments
and follow the
instructions.
•
If the dots still remain or there are obstacles that cannot be removed, such as whiteboard trays or
frames, go to step 14.
14.
If there is an obstacle that cannot be removed, such as a whiteboard tray or frame, remove the tape
from the back of the supplied infrared deflectors and stick them to the screen so that the laser is not
reflected by the obstacle.
Make sure to stick the deflectors between the dots and the obstacle and use as many deflectors as
necessary to match the width of the dots.
After placing the infrared deflectors, press the
or
button on the remote control, and then
repeat step 12.
If the dots do not disappear even after attaching the infrared deflectors, select
Additional
Adjustments
and follow the instructions
.
If the dots do not disappear even after performing the above procedures, contact Epson.
15.
Perform touch calibration by pressing
Menu
on the remote control. On the
Extended
menu, select
Easy Interactive Function
, then
Touch Unit Setup
. Select
Touch Calibration
and follow the
instructions.
❏
Do not remove an infrared deflector once it has been stuck in place.
❏
Do not stick tape or place anything on the infrared deflectors. The deflectors will
not function properly if anything is placed on them.