Epson Stylus COLOR 3000 User Manual - Epson Stylus RIP - Page 16

Preparing for Standalone Installation, Installing the StylusRIP Software

Get Epson Stylus COLOR 3000 - Ink Jet Printer PDF manuals and user guides View all Epson Stylus COLOR 3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Installing the StylusRIP Software Preparing for Standalone Installation If you connected the printer to a standalone Macintosh, you need to make AppleTalk active. Open the Chooser in the Apple menu and make sure AppleTalk is active. You must set your Network Control Panel to Remote only if you've connected your printer in one of these configurations:  You're using System 7.51 or lower and have connected the printer to the printer port on your Macintosh  You're using System 7.52 or higher and have connected the printer to the modem or printer port on your Macintosh and do not have an optional interface card installed For other configurations, go to "Installing on a Standalone or Print Server System" on the next page. Follow these steps to set up the printer as Remote only: 1. Restart your Macintosh with all extensions turned off except your CD-ROM drive. Then turn on your printer. 2. Insert the StylusRIP CD-ROM in the CD-ROM drive. 3. Locate the Extensions folder within the System folder on your hard disk drive. 4. Drag the Remote Only file from the CD-ROM to the System Extensions folder. 5. From the Apple menu, open the Control Panels utility. Click the Network icon and select Remote Only. (If your system uses the Open Transport protocol, there is no Network icon; in this case, open the AppleTalk folder and select Remote Only in the Connect via list box.) 1-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
Installing the StylusRIP Software
1-3
Preparing for Standalone Installation
If you connected the printer to a standalone Macintosh, you
need to make AppleTalk active. Open the Chooser in the Apple
menu and make sure AppleTalk is active.
You must set your Network Control Panel to Remote only if
you’ve connected your printer in one of these configurations:
You’re using System 7.51 or lower and have connected the
printer to the printer port on your Macintosh
You’re using System 7.52 or higher and have connected the
printer to the modem or printer port on your Macintosh
and
do not
have an optional interface card installed
For other configurations, go to “Installing on a Standalone or
Print Server System” on the next page.
Follow these steps to set up the printer as Remote only:
1.
Restart your Macintosh with all extensions turned off
except your CD-ROM drive. Then turn on your printer.
2.
Insert the StylusRIP CD-ROM in the CD-ROM drive.
3.
Locate the Extensions folder within the System folder on
your hard disk drive.
4.
Drag the
Remote Only
file from the CD-ROM to the
System Extensions folder.
5.
From the Apple menu, open the Control Panels utility.
Click the
Network
icon and select
Remote Only
. (If your
system uses the Open Transport protocol, there is no
Network
icon; in this case, open the AppleTalk folder and
select
Remote Only
in the
Connect via
list box.)