Epson Stylus COLOR 3000 User Manual - Epson Stylus RIP - Page 25

Printing with the StylusRIP Software, select the printer name. Or use

Get Epson Stylus COLOR 3000 - Ink Jet Printer PDF manuals and user guides View all Epson Stylus COLOR 3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Printing with the StylusRIP Software 3. Open the StylusRIP folder on the hard disk and double-click the StylusRIP Server icon. The first time you run the server software, you see a dialog box asking you to select your port or your printer name. 4. Select the printer or modem port if you connected the printer by serial cable. If you connected the printer by a network interface card and use AppleTalk zones, select the printer's zone and then select the printer name. Or use the Net Scan button to locate the printer on your network. Note: If you change your printer connection later, you must reconfigure StylusRIP for your new port. First, quit StylusRIP, turn off your printer, and disconnect it from the previously selected port or interface. Then connect the printer to the new port or interface. Open the StylusRIP folder on your hard disk and drag the CPSPref file into the trash. Then perform steps 1 through 3 in this section. When you see the Connection dialog box, select your printer on the new port or interface. 5. Click OK. The StylusRIP Server software searches for the updated printer and then prepares it for printing. 6. If you're using StylusRIP on a standalone Macintosh, quit the StylusRIP Server; you're ready to start printing. If you're using StylusRIP on a network, open the File menu and select Preferences. 2-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
Printing with the StylusRIP Software
2-2
3.
Open the StylusRIP folder on the hard disk and
double-click the
StylusRIP Server
icon. The first time you
run the server software, you see a dialog box asking you to
select your port or your printer name.
4.
Select the printer or modem port if you connected the
printer by serial cable.
If you connected the printer by a network interface card
and use AppleTalk zones, select the printer’s zone and then
select the printer name. Or use the
Net Scan
button to
locate the printer on your network.
Note:
If you change your printer connection later, you must
reconfigure StylusRIP for your new port. First, quit StylusRIP,
turn off your printer, and disconnect it from the previously
selected port or interface. Then connect the printer to the new
port or interface. Open the StylusRIP folder on your hard disk
and drag the CPSPref file into the trash. Then perform steps 1
through 3 in this section. When you see the Connection dialog
box, select your printer on the new port or interface.
5.
Click
OK
. The StylusRIP Server software searches for the
updated printer and then prepares it for printing.
6.
If you’re using StylusRIP on a standalone Macintosh, quit
the StylusRIP Server; you’re ready to start printing.
If you’re using StylusRIP on a network, open the File menu
and select
Preferences
.