Fujitsu 4340C Operator's Guide - Page 32

Connecting the interface cables, Setting the SCSI ID and the SCSI Terminator, NOTICE, ID No.

Get Fujitsu 4340C - fi - Document Scanner PDF manuals and user guides
UPC - 097564304156
View all Fujitsu 4340C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

I Connecting the interface cables 1. Connect the SCSI interface cables and secure them. . Back of the Image scanner Interface cables To the host system To the host system NOTICE 1. Factory default for the SCSI terminator is On. If the scanner is in the middle of the daisy chain or of two devices, turn the scanner termination Off via the operator panel. 2. The factory default for the SCSI ID is 5. If the ID of the scanner is the same as the other device, change the ID via the operator panel or change the ID of the other device. I Setting the SCSI ID and the SCSI Terminator The default of the SCSI ID is 5. The SCSI ID is set by using the Setup mode of the operator panel. 1. Turn the power Off by pressing the "0" side of the power switch. 2. Turn the SCSI-ID switch on the rear of the image scanner to set the SCSI-ID. ID No. 0 to 7 8, 9 Description Can be set Return to default (Available ID NO. = 5) if set to 8 or 9. 3. Set the SCSI terminator switch on the rear of the image scanner to ON or OFF. G 2-4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
●
2-4
■
Connecting the interface cables
1.
Connect the SCSI interface cables and secure them.
.
NOTICE
1. Factory default for the SCSI terminator is On. If the scanner is in the middle of the daisy chain or of two
devices, turn the scanner termination Off via the operator panel.
2. The factory default for the SCSI ID is 5. If the ID of the scanner is the same as the other device, change
the ID via the operator panel or change the ID of the other device.
■
Setting the SCSI ID and the SCSI Terminator
The default of the SCSI ID is 5. The SCSI ID is set by using the Setup mode of the operator panel.
1.
Turn the power Off by pressing the “0” side of the power switch.
2.
Turn the SCSI-ID switch on the rear of the image scanner to set the SCSI-ID.
3.
Set the SCSI terminator switch on the rear of the image scanner to ON or OFF.
ID No.
Description
0 to 7
Can be set
8, 9
Return to default (Available ID NO. = 5) if set to 8 or 9.