Gateway 9210 Gateway 9210 Server User Guide - Page 65

Changing jumper settings

Get Gateway 9210 PDF manuals and user guides View all Gateway 9210 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Changing jumper settings You can change the J1D1 jumper settings on the system board to: ■ Recover the BIOS configuration ■ Disable the BIOS Flash write-protect ■ Clear the current system password ■ Clear the CMOS To change jumper settings 1 Print the appendix for "BIOS Settings" on page 83. 2 Restart your server, then press F2 when the Gateway logo screen appears during startup. 3 Record any custom BIOS settings on your printout. 4 Follow the instructions in "Preventing static electricity discharge" on page 29. 5 Turn off the server, then disconnect the power cord and all other cables connected to the server. 6 Open the case. For instructions, see "Opening the server case" on page 30. Caution Moving the jumper while the power is on can damage your server. Always turn off the server and unplug the power cord and all other cables before changing the jumper. 7 Place a jumper across the indicated pins of jumper J1D1, as required, for the BIOS function you want to perform (see the following table). A BCD 60 www.gateway.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
60
www.gateway.com
Changing jumper settings
You can change the J1D1 jumper settings on the system board to:
■
Recover the BIOS configuration
■
Disable the BIOS Flash write-protect
■
Clear the current system password
■
Clear the CMOS
To change jumper settings
1
Print the appendix for
“BIOS Settings” on page 83
.
2
Restart your server, then press
F2
when the Gateway logo screen appears during
startup.
3
Record any custom BIOS settings on your printout.
4
Follow the instructions in
“Preventing static electricity discharge” on page 29
.
5
Turn off the server, then disconnect the power cord and all other cables connected
to the server.
6
Open the case. For instructions, see
“Opening the server case” on page 30
.
7
Place a jumper across the indicated pins of jumper J1D1, as required, for the BIOS
function you want to perform (see the following table).
Caution
Moving the jumper while the power is on can damage your
server. Always turn off the server and unplug the power
cord and all other cables before changing the jumper.
D
C
B
A