Gigabyte GA-M55plus-S3G Manual - Page 65

To con SATA hard drives, follow the steps below, Installing SATA hard drives in your computer

Get Gigabyte GA-M55plus-S3G PDF manuals and user guides View all Gigabyte GA-M55plus-S3G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

English 4-1-4 Configuring SATA Hard Drive(s) To configure SATA hard drive(s), follow the steps below: (1) Install SATA hard drive(s) in your system. (2) Configure SATA controller mode and boot sequence in BIOS Setup. (3) Configure RAID set in RAID BIOS. (Note ) (4) Make a floppy disk containing the SATA controller driver. (Note ) (5) Install the SATA controller driver during OS installation. (Note) Before you begin Please prepare: (a) SATA hard drive(s). To ensure optimal performance, it is recommended that you use two hard drives with identical model and capacity for RAID array. If you do not want to create RAID, you may prepare only one hard drive. (b) An empty formatted floppy disk. (Note ) (c) Windows XP/2000 setup disk. (d) Driver CD for your motherboard. (Note ) (1) Installing SATA hard drive(s) in your computer Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA port(s) on the motherboard. Then connect the power connector from your power supply to the hard drive. (Note) Required for setting up RAID array. - 65 - Appendix

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Appendix
- 65 -
English
(Note)
Required for setting up RAID array.
To configure SATA hard drive(s), follow the steps below:
(1)
Install SATA hard drive(s) in your system.
(2)
Configure SATA controller mode and boot sequence in BIOS Setup.
(3)
Configure RAID set in RAID BIOS.
(Note )
(4)
Make a floppy disk containing the SATA controller driver.
(Note )
(5)
Install the SATA controller driver during OS installation.
(Note )
Before you begin
Please prepare:
(a)
SATA hard drive(s). To ensure optimal performance, it is recommended that you use two hard
drives with identical model and capacity for RAID array. If you do not want to create RAID, you
may prepare only one hard drive.
(b)
An empty formatted floppy disk.
(Note )
(c)
Windows XP/2000 setup disk.
(d)
Driver CD for your motherboard.
(Note )
(1)
Installing SATA hard drive(s) in your computer
Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available
SATA port(s) on the motherboard. Then connect the power connector from your power supply to the
hard drive.
4-1-4
Configuring SATA Hard Drive(s)