54
CONFIGURING THE REMOTE
CONFIGURING THE REMOTE
Channel Punch-Through
Channel punch-through allows the Channel Up/Down
buttons to send commands to a different device than
the one selected for other commands. For example,
you may wish to use a cable box or satellite receiver
as the source for a VCR, so you would
want the
Channel Up/Down Buttons
µ
to transmit com-
mands to the cable box even though the other button
commands are programmed to operate the VCR.
To program the remote for channel punch-through,
follow these steps. This example will show how to
program channel punch-through so that the com-
mands programmed for Channel Up/Down for the
VID 3/Cable device will be transmitted when the
VID 1/VCR device has been selected as the
current device.
1. Press and hold the
Program Button
O
for
about 3 seconds while the message shown
in Figure 26 appears in the remote’s
LCD
Information Display
2
. Release the button
when the red light under the
Set Button
F
appears.
2. The remote’s
MAIN MENU
message (Figure
27), will appear in the LCD and the
Set Button
F
will remain illuminated in red. Press the
⁄
/
¤
Navigation Button
D
until
PUNCH-
THROUGH
appears on the bottom line of the
LCD screen, as shown in Figure 60. Press the
Set Button
F
to enter the main punch-through
menu branch.
3. At the next menu screen, press the
⁄
/
¤
Navigation Button
D
until
CHANNEL
appears on the bottom line of the LCD screen,
as shown in Figure 66. Press the
Set Button
F
to begin programming the remote for
Channel punch-through.
Figure 66
4. The next display screen (Figure 67) is where you
select the device that will receive the punch-
through commands. In our example, that is the
VID 2/
TV button, as that is where we want the
cable box’s channel controls to be active. Press
the
⁄
/
¤
Navigation Button
D
until the
name of the base device appears and then
press the
Set Button
F
.
Figure 67
5. At the next display screen (Figure 68), you will
select the device whose Channel Up/Down com-
mands will be used. Press the
⁄
/
¤
Navigation
Button
D
until the desired device name
appears to the right of the device in use. In
our example, that is the cable box. When the
desired combination of devices appears, press
the
Set Button
F
.
Figure 68
6. When the Set button is pressed, the display will
change to show you that the new combination
of control commands is being saved to the unit’s
memory, as shown in Figure 69. The word
SAVED
will flash four times and then the
remote will return to normal operation.
Figure 69
7. Once the punch-through is programmed, the
Channel Up/Down Buttons of the second device
named will be used when those buttons
µ
are
pressed while the master device is in use.
Returning the Channel Control Settings to
Default Operation
If you wish to remove the Channel Punch-Through
so that the commands for Channel Up/Down are
returned to the factory default setting, follow the steps
shown above, except that in Steps 4 and 5, select
the same device for both the
DEVICE IN USE
on
the left side of the bottom line and the
PUNCH-
THROUGH
device. In the example used, the display
to return the remote to default settings will appear as
shown in Figure 70.
Figure 70
Transport Punch-Through
The
Play
G
, Stop
J
, Fast Forward/Reverse
I
, Pause
J
, Record
J
and
Skip Up/Down
K
Transport Controls are set at the factory to oper-
ate your DVD player, or the controls of a specific
device such as a VCR or CD player when they are
selected. However, by using the Transport Punch-
Through feature you may program these controls to
transmit the commands for a different device. For
example, you may wish to operate the transport of a
second VCR connected to the VID 2/TV input, as
shown in the following example.
1. Press and hold the
Program Button
O
for
about 3 seconds while the message shown
in Figure 26 appears in the remote’s
LCD
Information Display
2
. Release the button
when the light under the
Set Button
F
turns red.
2. The remote’s
MAIN MENU
message (Figure
27), will appear in the LCD and the
Set Button
F
will remain illuminated in red. Press the
⁄
/
¤
Navigation Button
D
until
PUNCH-
THROUGH
appears on the bottom line of the
LCD screen, as shown in Figure 60. Press the
Set Button
F
to enter the main punch-through
menu branch.
3. At the next menu screen, press the
⁄
/
¤
Navigation Button
D
until
TRANSPORT
appears on the bottom line of the LCD screen, as
shown in Figure 71. Press the
Set Button
F
to begin programming the remote for transport
punch-through.
Figure 71
4. The next display screen (Figure 72) selects the
device that will receive the punch-through com-
mands. In our example, that is the TV button, as
that is where we want the VCR’s transport controls
to be active. Press the
⁄
/
¤
Navigation Button
D
until the name of the base device appears
and then press the
Set Button
F
.
Figure 72
5. At the next display screen (Figure 73), select the
device whose transport commands will be used.
Press the
⁄
/
¤
Navigation Button
D
until the
desired device name appears to the right of the
device in use. In our example, that is the VCR.
When the desired combination of devices
appears, press the
Set Button
F
.
Figure 73
6. When the Set button is pressed, the display will
change to show you that the new combination of
control commands is being saved to the unit’s
memory, as shown in Figure 74. The word
SAVED
will flash four times and then the
remote will return to normal operation.
Figure 74
7. Once the punch-through is programmed, the
transport buttons of the second device named
will be used when those buttons are pressed
while the master device is in use.
TV
<
-VCR [TRS]
SAVED
PUNCH-THROUGH
TV
<
-VCR
DEVICE IN USE
TV
PUNCH-THROUGH
TRANSPORT
PUNCH-THROUGH
VCR
<
-VCR
VCR
<
-CBL [CHAN]
SAVED
PUNCH-THROUGH
VCR
<
-CBL
DEVICE IN USE
VCR
PUNCH-THROUGH
CHANNEL
1
49
50
51
52
53
54
55
56
57
58
59
