HP 12000 HP StorageWorks 12000 Gateway Virtual Library System User Guide (AH81 - Page 33

Multi-node Setup, Configuring Primary Node 0, Configuring the Secondary Nodes 1 through 7

Get HP 12000 PDF manuals and user guides View all HP 12000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

3 Multi-node Setup This section explains how to configure the identities of each node after the VLS12000 Gateway is physically installed. Configuring Primary Node 0 To configure the primary node: 1. On the primary node, connect to the serial port or use the keyboard and mouse ports to connect to a console. 2. Power on the primary node. After several minutes, a menu will appear on your monitor asking whether the node is a primary (master, m) or secondary (slave, s) node. 3. Enter m. The node will then run cable checks and configuration checks. 4. After the checks are complete the node will reboot automatically. Wait for the primary node to fully boot. Rebooting is complete when you receive the "Initializing node#" and then "Initializing for node# completed." messages in the systems notifications (if you have DHCP enabled) of Command View VLS or when you see the login prompt on the terminal. 5. Set the IP address and other public network configurations on the VLS. Refer to Setting the Network Settings for instructions. Configuring the Secondary Nodes 1 through 7 To configure the secondary nodes (nodes 1 through 7): 1. On the secondary node, connect to the serial port or use the keyboard and mouse ports to connect to a console. 2. Power on the primary node and all previously installed secondary nodes of the VLS. 3. Power on the secondary node being added to the VLS. After several minutes, a menu will appear on your monitor asking whether the node is a primary (master, m) or secondary (slave, s) node. 4. Enter s. HP StorageWorks 12000 Gateway Virtual Library System User Guide 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
3 Multi-node Setup
This section explains how to configure the identities of each node after the VLS12000 Gateway is
physically installed.
Configuring Primary Node 0
To configure the primary node:
1.
On the primary node, connect to the serial port or use the keyboard and mouse ports to connect
to a console.
2.
Power on the primary node.
After several minutes, a menu will appear on your monitor asking whether the node is a primary
(master, m) or secondary (slave, s) node.
3.
Enter
m
. The node will then run cable checks and configuration checks.
4.
After the checks are complete the node will reboot automatically. Wait for the primary node to
fully boot.
Rebooting is complete when you receive the
“
Initializing node#
”
and then
“
Initializing for node#
completed.
”
messages in the systems notifications (if you have DHCP enabled) of Command View
VLS or when you see the login prompt on the terminal.
5.
Set the IP address and other public network configurations on the VLS. Refer to
Setting the Network
Settings
for instructions.
Configuring the Secondary Nodes 1 through 7
To configure the secondary nodes (nodes 1 through 7):
1.
On the secondary node, connect to the serial port or use the keyboard and mouse ports to connect
to a console.
2.
Power on the primary node and all previously installed secondary nodes of the VLS.
3.
Power on the secondary node being added to the VLS.
After several minutes, a menu will appear on your monitor asking whether the node is a primary
(master, m) or secondary (slave, s) node.
4.
Enter
s
.
HP StorageWorks 12000 Gateway Virtual Library System User Guide
33