HP 1606 HP StorageWorks Fabric OS 6.3.1c Release Notes (5697-0509 September 2 - Page 43

HP StorageWorks Fabric OS 6.3.1c Release Notes, The disable EE interface CLI

Get HP 1606 PDF manuals and user guides View all HP 1606 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

which will in turn remove the associated frame redirection zone information. Make sure to back up all data before taking this action. • Before committing configurations or modifications to the CTC or LUNs on an HP Encryption Switch or HP Encryption Blade, make sure that there are no outstanding zoning transactions in the switch or fabric. Failure to do so results in the commit operation for the CTC or LUNs failing and may cause the LUNs to be disabled. The user can check for outstanding zoning transactions by issuing the CLI command cfgtransshow: DCX_two:root> cfgtransshow There is no outstanding zoning transaction • Each LUN is uniquely identified by the HP Encryption Switch or HP Encryption Blade using the LUN's serial number. The LUN serial numbers must be unique for LUNs exposed from the same target port. The LUN serial numbers must also be unique for LUNs belonging to different target ports in nonmultipathing configurations. Failure to ensure unique LUN serial numbers results in nondeterministic behavior and may result in faulting of the HP Encryption Switch or HP Encryption Blade. • When creating an HA cluster or EG with two or more HP Encryption Switch/Encryption Blades, the GE ports (I/O sync links) must be configured with an IP address for the eth0 and eth1 Ethernet interfaces using ipaddrset. In addition, the eth0 and eth1 Ethernet ports should be connected to the network for redundancy. These I/O sync links connections must be established before any Re-Key, First Time Encryption, or enabling EE for crypto operations. Failure to do so results in HA Cluster creation failure. If the IP address for these ports is configured after the EE was enabled for encryption, HP Encryption Switch needs to be rebooted and Encryption Blades should be slotpoweroff/slotpoweron to sync up the IP address information to the EEs. If only one Ethernet port is configured and connected to a network, data loss or suspension of Re-Key may occur when the network connection toggles or fails. • initEE will remove the existing master key or link key. Backup the master key by running cryptocfg -exportmasterkey and cryptocfg -export -currentMK before running initEE. After initEE, regEE and enableEE, run cryptocfg -recovermasterkey to recover the master key previously backed up, or in the case of fresh install run cryptocfg - genmasterkey to generate a new master key. If you are using SKM, establish a trusted link with SKM again. Certificate exchange between key vaults and switches are not required in this case. • The disable EE interface CLI cryptocfg --disableEE [slot no] should be used only to disable encryption and security capabilities of the EE from the Fabric OS Security Admin in the event of a security compromise. When disabling the encryption capabilities of the EE using the noted commands, the EE should not be hosting any CTCs. Ensure that all CTCs hosted on the HP Encryption Switch or HP Encryption Blade are either removed or moved to a different EE in the HA Cluster or EG before disabling the encryption and security capabilities. • Whenever initNode is performed, new certificates for CP and KAC (SKM) are generated. Hence, each time InitNode is performed, the new KAC Certificate must be loaded onto key vaults for (SKM. Without this step, errors will occur, such as key vault not responding and ultimately key archival and retrieval problems. • The HTTP server should be listening to port 9443. SKM is supported only when configured to port 9443. • Configuring a Brocade group on SKM: As described in the Fabric OS Encryption Administrator's Guide, a Brocade group needs to be configured on SKM (under Local Users & Groups) for managing all keys generated by Brocade encryption switches and blades. It is important to note that the name for this group is case sensitive and must be "brocade," not "Brocade." • When all nodes in an EG (HA Cluster or DEK Cluster) are powered down (due to catastrophic disaster or a power outage to the data center) and later nodes come back online (in the event of the Group Leader (GL) node failing to come back up or the GL node being kept powered down) the member nodes lose information and knowledge about the EG. This leads to no crypto operations HP StorageWorks Fabric OS 6.3.1c Release Notes 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
which will in turn remove the associated frame redirection zone information. Make sure to back
up all data before taking this action.
•
Before committing configurations or modifications to the CTC or LUNs on an HP Encryption Switch
or HP Encryption Blade, make sure that there are no outstanding zoning transactions in the switch
or fabric. Failure to do so results in the commit operation for the CTC or LUNs failing and may
cause the LUNs to be disabled. The user can check for outstanding zoning transactions by issuing
the CLI command
cfgtransshow
:
DCX_two:root> cfgtransshow
There is no outstanding zoning transaction
•
Each LUN is uniquely identified by the HP Encryption Switch or HP Encryption Blade using the
LUN
’
s serial number. The LUN serial numbers must be unique for LUNs exposed from the same
target port. The LUN serial numbers must also be unique for LUNs belonging to different target
ports in nonmultipathing configurations. Failure to ensure unique LUN serial numbers results in
nondeterministic behavior and may result in faulting of the HP Encryption Switch or HP Encryption
Blade.
•
When creating an HA cluster or EG with two or more HP Encryption Switch/Encryption Blades,
the GE ports (I/O sync links) must be configured with an IP address for the
eth0
and
eth1
Ethernet
interfaces using
ipaddrset
. In addition, the
eth0
and
eth1
Ethernet ports should be connected
to the network for redundancy. These I/O sync links connections must be established before any
Re-Key, First Time Encryption, or enabling EE for crypto operations. Failure to do so results in HA
Cluster creation failure. If the IP address for these ports is configured after the EE was enabled for
encryption, HP Encryption Switch needs to be rebooted and Encryption Blades should be
slot-
poweroff
/
slotpoweron
to sync up the IP address information to the EEs. If only one Ethernet
port is configured and connected to a network, data loss or suspension of Re-Key may occur when
the network connection toggles or fails.
•
initEE
will remove the existing master key or link key. Backup the master key by running
cryptocfg –exportmasterkey
and
cryptocfg –export –currentMK
before running
initEE
. After
initEE
,
regEE
and
enableEE
, run
cryptocfg –recovermasterkey
to re-
cover the master key previously backed up, or in the case of fresh install run
cryptocfg –
genmasterkey
to generate a new master key. If you are using SKM, establish a trusted link with
SKM again. Certificate exchange between key vaults and switches are not required in this case.
•
The disable EE interface CLI
cryptocfg --disableEE [slot no]
should be used only to
disable encryption and security capabilities of the EE from the Fabric OS Security Admin in the
event of a security compromise. When disabling the encryption capabilities of the EE using the
noted commands, the EE should not be hosting any CTCs. Ensure that all CTCs hosted on the HP
Encryption Switch or HP Encryption Blade are either removed or moved to a different EE in the
HA Cluster or EG before disabling the encryption and security capabilities.
•
Whenever
initNode
is performed, new certificates for CP and KAC (SKM) are generated. Hence,
each time
InitNode
is performed, the new KAC Certificate must be loaded onto key vaults for
(SKM. Without this step, errors will occur, such as key vault not responding and ultimately key
archival and retrieval problems.
•
The HTTP server should be listening to port 9443. SKM is supported only when configured to port
9443.
•
Configuring a Brocade group on SKM: As described in the
Fabric OS Encryption Administrator's
Guide
, a Brocade group needs to be configured on SKM (under Local Users & Groups) for man-
aging all keys generated by Brocade encryption switches and blades. It is important to note that
the name for this group is case sensitive and must be
“
brocade,
”
not
“
Brocade.
”
•
When all nodes in an EG (HA Cluster or DEK Cluster) are powered down (due to catastrophic
disaster or a power outage to the data center) and later nodes come back online (in the event of
the Group Leader (GL) node failing to come back up or the GL node being kept powered down)
the member nodes lose information and knowledge about the EG. This leads to no crypto operations
HP StorageWorks Fabric OS 6.3.1c Release Notes
43