HP 1606 HP StorageWorks Fabric OS 6.3.1c Release Notes (5697-0509 September 2 - Page 85

the HP StorageWorks DC SAN Backbone

Get HP 1606 PDF manuals and user guides View all HP 1606 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

Invalid zone name does not cause error message, and no enforcement of 64 character limit on cfg/zone name. Functional impact is zone is Fixed in Fabric OS 6.3.1 not enabled. Test loop that continuously opens and closes Telnet sessions and does terminal configuration on the 2408 FCoE switch or 10/24 FCoE blade sometimes the configure terminal command fails and the config prompt does not appear. Fixed in Fabric OS 6.3.1 Username/password authentication can fail when using Microsoft Active Directory (LDAP) from Server 2008 for authentication. User may experience problems after upgrade from a Microsoft Windows host using older versions of the LDAP protocol for authentications. Fixed in Fabric OS 6.3.1 User must remove trial licenses before installing permanent licenses for the same features or switch disruption can occur. The fix will automatically remove/replace the trial license before adding the permanent license, avoiding any disruption. Fixed in Fabric OS 6.3.1 After using the snmpconfig -set snmpv command to set SNMPv3, the switch configdownload command failed with the following mes- Fixed in Fabric OS 6.3.1 sage: snmp.snmpv3Usm.0.usmPrivProtocol:6 Invalid Value. After removal and insertion of the HP StorageWorks Encryption blade, the lscfg --show command will show ASIC not ready errors and FW-5002 will be observed in the internal raslog. Fixed in Fabric OS 6.3.1 Encryption blade or switch faults and weblinker crashes when stressed Fixed in Fabric OS 6.3.1 with heavy I/O and constant stats gathering. If you set fwsettocustom, the HP StorageWorks DC SAN Backbone Director does not output FW-1003/FW-1004 after an hafailover or reboot, and you will not be notified about temperature over threshold events. Fixed in Fabric OS 6.3.1 CALD panic occurs in switch with a large number of F_Ports (>=50) configured with top talkers after switchdisable/switchenable stress test. Fixed in Fabric OS 6.3.1 With the 2408 FCoE switch or 10/24 FCoE blade, ssmd will crash when acl's, whose name starts with a numeric value are cleared. Fixed in Fabric OS 6.3.1 The systemverification and portloopbacktest diagnostic tests report marginal blade failures on an HP StorageWorks DC SAN Director, but after the tests are complete, Fabric Watch reports switch is healthy. Fixed in Fabric OS 6.3.1 Based on the way the physical connections are made on an ICL between a DC SAN Backbone director and a DC04 SAN director, only half the expected E_Ports (links) are coming online when an 8-link ICL license is installed. Fixed in Fabric OS 6.3.1 HP StorageWorks Fabric OS 6.3.1c Release Notes 85

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Fixed in Fabric OS 6.3.1
Invalid zone name does not cause error message, and no enforcement
of 64 character limit on cfg/zone name. Functional impact is zone is
not enabled.
Fixed in Fabric OS 6.3.1
Test loop that continuously opens and closes Telnet sessions and does
terminal configuration on the 2408 FCoE switch or 10/24 FCoE blade
sometimes the
configure terminal
command fails and the
config
prompt does not appear.
Fixed in Fabric OS 6.3.1
Username/password authentication can fail when using Microsoft Active
Directory (LDAP) from Server 2008 for authentication. User may exper-
ience problems after upgrade from a Microsoft Windows host using
older versions of the LDAP protocol for authentications.
Fixed in Fabric OS 6.3.1
User must remove trial licenses before installing permanent licenses for
the same features or switch disruption can occur. The fix will automatic-
ally remove/replace the trial license before adding the permanent li-
cense, avoiding any disruption.
Fixed in Fabric OS 6.3.1
After using the
snmpconfig -set snmpv
command to set SNMPv3,
the switch
configdownload
command failed with the following mes-
sage:
snmp.snmpv3Usm.0.usmPrivProtocol:6 Invalid Value
.
Fixed in Fabric OS 6.3.1
After removal and insertion of the HP StorageWorks Encryption blade,
the
lscfg --show
command will show
ASIC not ready
errors
and
FW-5002
will be observed in the internal raslog.
Fixed in Fabric OS 6.3.1
Encryption blade or switch faults and weblinker crashes when stressed
with heavy I/O and constant stats gathering.
Fixed in Fabric OS 6.3.1
If you set
fwsettocustom
, the HP StorageWorks DC SAN Backbone
Director does not output FW-1003/FW-1004 after an
hafailover
or reboot, and you will not be notified about temperature over threshold
events.
Fixed in Fabric OS 6.3.1
CALD panic occurs in switch with a large number of F_Ports (>=50)
configured with top talkers after
switchdisable
/
switchenable
stress test.
Fixed in Fabric OS 6.3.1
With the 2408 FCoE switch or 10/24 FCoE blade, ssmd will crash
when acl's, whose name starts with a numeric value are cleared.
Fixed in Fabric OS 6.3.1
The
systemverification
and
portloopbacktest
diagnostic
tests report marginal blade failures on an HP StorageWorks DC SAN
Director, but after the tests are complete, Fabric Watch reports switch
is healthy.
Fixed in Fabric OS 6.3.1
Based on the way the physical connections are made on an ICL between
a DC SAN Backbone director and a DC04 SAN director, only half the
expected E_Ports (links) are coming online when an 8-link ICL license
is installed.
HP StorageWorks Fabric OS 6.3.1c Release Notes
85