HP 3PAR StoreServ 7450 4-node HP 3PAR StoreServ 7450 Storage Installation Guid - Page 22

Installing PCIe Adapters in the Controller Nodes, Installing Enclosures, WARNING, CAUTION

Get HP 3PAR StoreServ 7450 4-node PDF manuals and user guides View all HP 3PAR StoreServ 7450 4-node manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Installing PCIe Adapters in the Controller Nodes PCIe adapters connect the controller nodes to host computers and hard drives. Installing or upgrading PCle adapters involves adding additional supported types of adapters or replacing existing adapters. WARNING! FC HBA and iSCSI CNA upgrades on the HP 3PAR StoreServ 7450 four controller node system must be serviced by authorized service personnel and cannot be done by a customer. Contact your local service provider for assistance. Upgrades on the HP 3PAR StoreServ 7450 two controller node system may be performed by the customer. CAUTION: To avoid possible data loss, only one node at a time should be removed from the storage system. To prevent overheating, node replacement requires a maximum service time of 30 minutes. NOTE: When installing the first two HBAs or CNAs in a controller node, install the HBAs in node 0 and node 1. If two FC HBAs and two CNA HBAs are added to a controller node, install the FC HBAs in node 0 and node 1, and then install the CNA HBAs in node 2 and node 3. 1. Remove the controller node and then the cover. 2. If a PCIe Adapter Assembly is already installed, do the following steps: a. Remove the PCIe Adapter Assembly, and disconnect the PCIe Adapter from the riser card. b. Install the new PCIe Adapter onto the riser card, and insert the assembly into the node. 3. If a PCIe Adapter is not installed, do the following steps: a. Remove the PCIe Adapter riser card. b. Install the new PCIe Adapter onto the riser card, and insert the assembly into the node. 4. Replace the node cover and the node. Installing Enclosures The storage system can contain the following types of drive and controller node enclosures: 2U and 4U enclosures. WARNING! The enclosure is heavy. Lifting, moving, or installing the enclosure requires two people. NOTE: When installing a 7450 two controller node enclosure, two units of space must be reserved above the enclosure for an upgrade to a four-node system. Labels are provided to secure on two filler panels to reserve this space. To install an enclosure on the rack: 22 Installing Storage System Components into a Rack

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
Installing PCIe Adapters in the Controller Nodes
PCIe adapters connect the controller nodes to host computers and hard drives. Installing or
upgrading PCle adapters involves adding additional supported types of adapters or replacing
existing adapters.
WARNING!
FC HBA and iSCSI CNA upgrades on the HP 3PAR StoreServ 7450 four controller
node system must be serviced by authorized service personnel and cannot be done by a customer.
Contact your local service provider for assistance. Upgrades on the HP 3PAR StoreServ 7450 two
controller node system may be performed by the customer.
CAUTION:
To avoid possible data loss, only one node at a time should be removed from the
storage system. To prevent overheating, node replacement requires a maximum service time of 30
minutes.
NOTE:
When installing the first two HBAs or CNAs in a controller node, install the HBAs in node
0 and node 1. If two FC HBAs and two CNA HBAs are added to a controller node, install the FC
HBAs in node 0 and node 1, and then install the CNA HBAs in node 2 and node 3.
1.
Remove the controller node and then the cover.
2.
If a PCIe Adapter Assembly is already installed, do the following steps:
a.
Remove the PCIe Adapter Assembly, and disconnect the PCIe Adapter from the riser card.
b.
Install the new PCIe Adapter onto the riser card, and insert the assembly into the node.
3.
If a PCIe Adapter is not installed, do the following steps:
a.
Remove the PCIe Adapter riser card.
b.
Install the new PCIe Adapter onto the riser card, and insert the assembly into the node.
4.
Replace the node cover and the node.
Installing Enclosures
The storage system can contain the following types of drive and controller node enclosures: 2U
and 4U enclosures.
WARNING!
The enclosure is heavy. Lifting, moving, or installing the enclosure requires two
people.
NOTE:
When installing a 7450 two controller node enclosure, two units of space must be reserved
above the enclosure for an upgrade to a four-node system. Labels are provided to secure on two
filler panels to reserve this space.
To install an enclosure on the rack:
22
Installing Storage System Components into a Rack