HP 3PAR StoreServ 7450 4-node HP 3PAR StoreServ 7450 Storage Installation Guid - Page 27

Installing the Service Processor in the Storage System

Get HP 3PAR StoreServ 7450 4-node PDF manuals and user guides View all HP 3PAR StoreServ 7450 4-node manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Installing the Service Processor in the Storage System The HP 3PAR Service Processor consists of the following: • A standard HP Server • A 1U Rail Kit for that specific server NOTE: The SP ID is the HP 7-digit serial number of the array located on the top front of the server and in a pull-out placard in the front of the server. The serial number is preceded by SP000. For example, if the 3PAR serial number is 1614983, enter SP0001614983. Use these procedures when installing an HP 3PAR Service Processor in an existing rack. Before you begin, verify that you have the proper service processor 1U Mounting Kit (PN 683811-001). The service processor rail kit supports a variety of products in round, square, or threaded-hole racks. The following table identifies any tools required for each type of rack. Table 4 Rack Types Rack Type Round hole Tools Required None Picture Square hole None Threaded hole Screwdriver The following components are included in the kit: • Slide mounting rails • Screws • Cage nuts (for the round-hole rack) • Cable management straps • Labels Installing the Service Processor in the Storage System 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
Installing the Service Processor in the Storage System
The HP 3PAR Service Processor consists of the following:
•
A standard HP Server
•
A 1U Rail Kit for that specific server
NOTE:
The SP ID is the HP 7-digit serial number of the array located on the top front of the server
and in a pull-out placard in the front of the server. The serial number is preceded by
SP000
. For
example, if the 3PAR serial number is 1614983, enter
SP0001614983
.
Use these procedures when installing an HP 3PAR Service Processor in an existing rack. Before
you begin, verify that you have the proper service processor 1U Mounting Kit (PN 683811-001).
The service processor rail kit supports a variety of products in round, square, or threaded-hole
racks. The following table identifies any tools required for each type of rack.
Table 4 Rack Types
Picture
Tools Required
Rack Type
None
Round hole
None
Square hole
Screwdriver
Threaded hole
The following components are included in the kit:
•
Slide mounting rails
•
Screws
•
Cage nuts (for the round-hole rack)
•
Cable management straps
•
Labels
Installing the Service Processor in the Storage System
27