HP 3PAR StoreServ 7450 4-node HP 3PAR StoreServ 7450 Storage Installation Guid - Page 51

Setting Up the Service Processor and Storage System, Storage System Software Installation

Get HP 3PAR StoreServ 7450 4-node PDF manuals and user guides View all HP 3PAR StoreServ 7450 4-node manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

8 Setting Up the Service Processor and Storage System Before you begin setting up the storage system, review and complete the following tasks: • Complete the storage system installation checklist below. • Verify Microsoft Windows 2008 R2 or 2012 is currently running. Windows 2008 R2 or 2012 is required to perform host configurations. If the system does not meet the requirements, you can proceed with the software installation without using HP 3PAR SmartStart. Storage System Software Installation Checklist Verify the following before you begin the installation process: • All components are installed. • Review the storage system setup and make sure it is powered on. • All LEDs are properly functioning. • The SP is installed, powered on, and assigned an IP address; or the VSP is installed and connected, and the temporary IP address is determined. • The SP connection is established. Table 12 SP and Storage System Software Installation Checklist HP 3PAR Service Processor StoreServ serial number NOTE: The StoreServ 7-digit serial number is located on the back of your HP 3PAR storage system next to the power switch for the node enclosure PCM, and it begins with16 (for example, 1624635). Service Processor Host Name NOTE: During the SP Setup process, the StoreServ must be powered on, connected to the same network subnet as the SP, and non-initialized to allow the SP to verify the StoreServ serial number. Permanent IP address (IPv4 only) Subnet mask Gateway IP address DNS settings: Domain name DNS servers Maximum supported speed and duplex setting: Autonegotiate or Custom duplex (half or full) and Custom speed (10, 100, or 1000 MB/s) Proxy server settings for Remote Support (if applicable): Protocol Address and port Authentication information (optional) System Support Information: • Installation site information • Customer information Storage System Software Installation Checklist 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
8 Setting Up the Service Processor and Storage System
Before you begin setting up the storage system, review and complete the following tasks:
•
Complete the storage system installation checklist below.
•
Verify Microsoft Windows 2008 R2 or 2012 is currently running. Windows 2008 R2 or 2012
is required to perform host configurations. If the system does not meet the requirements, you
can proceed with the software installation without using HP 3PAR SmartStart.
Storage System Software Installation Checklist
Verify the following before you begin the installation process:
•
All components are installed.
•
Review the storage system setup and make sure it is powered on.
•
All LEDs are properly functioning.
•
The SP is installed, powered on, and assigned an IP address; or the VSP is installed and
connected, and the temporary IP address is determined.
•
The SP connection is established.
Table 12 SP and Storage System Software Installation Checklist
HP 3PAR Service Processor
StoreServ serial number
NOTE:
The StoreServ 7–digit serial number is located on the back of your HP
3PAR storage system next to the power switch for the node enclosure PCM, and it
begins with
16
(for example, 1624635).
Service Processor Host Name
NOTE:
During the SP Setup process, the StoreServ must be powered on, connected
to the same network subnet as the SP, and non-initialized to allow the SP to verify
the StoreServ serial number.
Permanent IP address (IPv4 only)
Subnet mask
Gateway IP address
DNS settings:
Domain name
DNS servers
Maximum supported speed and duplex setting:
Autonegotiate or
Custom duplex (half or full) and
Custom speed (10, 100, or 1000 MB/s)
Proxy server settings for Remote Support (if applicable):
Protocol
Address and port
Authentication information (optional)
System Support Information:
•
Installation site information
•
Customer information
Storage System Software Installation Checklist
51