HP 3PAR StoreServ 7450 4-node HP 3PAR StoreServ 7450 Storage Installation Guid - Page 36

Cabling the Power Distribution Unit, Cabling the Power Strips

Get HP 3PAR StoreServ 7450 4-node PDF manuals and user guides View all HP 3PAR StoreServ 7450 4-node manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

NOTE: Before inserting the power cords into the PCMs, verify the PCM power switch is set to 0 (off). 2. Route the main power cords to a power strip or PDU. Ensure the routed cords maintain proper service clearance. 3. Insert each end of the power cord into the power strip/PDU and PCM. Fasten the PCM power cord using the restraining clip on each PCM. NOTE: Do not power on the PCMs at this time. Cabling the Power Distribution Unit PDUs can be mounted horizontally below the enclosures at the bottom of the rack. Each PDU AC cord connects to the appropriate outlet based on the type of cord and power requirements to supply power to the storage system. To access the vertically mounted PDUs or servicing area, the PDUs can be lowered out of the rack. 1. Remove the two top mounting screws. 2. Pull down on the PDU to lower. NOTE: If necessary, loosen the two bottom screws to unhinge the bracket before pulling down the PDU. 3. Ensure the PDUs are in a fully lowered position before accessing. Figure 34 Disengaging the PDU Pivot Brackets Cabling the Power Strips Power strips can be located on the side of the rack to supply power to the PCMs. Power strips are connected to PDUs. Do not exceed the capabilities of power strips and PDUs. Continue on to "Verifying Setup and Powering On the Storage System" (page 37). 36 Cabling the Storage System

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
NOTE:
Before inserting the power cords into the PCMs, verify the PCM power switch is set
to 0 (off).
2.
Route the main power cords to a power strip or PDU. Ensure the routed cords maintain proper
service clearance.
3.
Insert each end of the power cord into the power strip/PDU and PCM. Fasten the PCM power
cord using the restraining clip on each PCM.
NOTE:
Do not power on the PCMs at this time.
Cabling the Power Distribution Unit
PDUs can be mounted horizontally below the enclosures at the bottom of the rack. Each PDU AC
cord connects to the appropriate outlet based on the type of cord and power requirements to
supply power to the storage system.
To access the vertically mounted PDUs or servicing area, the PDUs can be lowered out of the rack.
1.
Remove the two top mounting screws.
2.
Pull down on the PDU to lower.
NOTE:
If necessary, loosen the two bottom screws to unhinge the bracket before pulling
down the PDU.
3.
Ensure the PDUs are in a fully lowered position before accessing.
Figure 34 Disengaging the PDU Pivot Brackets
Cabling the Power Strips
Power strips can be located on the side of the rack to supply power to the PCMs. Power strips are
connected to PDUs. Do not exceed the capabilities of power strips and PDUs.
Continue on to
“Verifying Setup and Powering On the Storage System” (page 37)
.
36
Cabling the Storage System