HP 4400 HP B-series Fabric OS 7.0.0a Release Notes (5697-0881, June 2011) - Page 50

or the HP DC SAN Director 10/24 FCoE Blade could crash the HP

Get HP 4400 PDF manuals and user guides View all HP 4400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Closed fixes summary There is no column for discard_C3_timeout_only in porterrshow. Solution Workaround prior to upgrade:Users should use the portstatsshow CLI to find the c3 Rx and Tx timeout discards as the porterrshow CLI will only show the summation of many c3 discards. Fixed in Fabric OS 7.0.0. The Port Admin window indicates Online/Healthy, yet additional port Info indicates the port is segmented. Fixed in Fabric OS 7.0.0. In a FICON environment, FICON CUP cannot be enabled when a faulted blade exists in the chassis. Fixed in Fabric OS 7.0.0. After enabling https, a failover will cause the active CP to still be running http and users will not have https services after a failover. Workaround prior to upgrade:Issue another HA Failover to cause both CPs to reset the web services. Fixed in Fabric OS 7.0.0. In Access Gateway mode, devices with QoS enabled on HBA and F_Port and N_Port would intermittently come online without the AoQ bit set. Fixed in Fabric OS 7.0.0. Removal of the HP StorageWorks B-Series Multi-protocol Router Blade or the HP DC SAN Director 10/24 FCoE Blade could crash the HP Fixed in Fabric OS 7.0.0. StorageWorks DC SAN Backbone Director Switch during POST. FAN frames are not being sent by the switch to loop devices after LIP when fcAL.fanFrameDisable is set to 0. Fixed in Fabric OS 7.0.0. The HP 2408 FCoE Switch and HP DC SAN Director 10/24 FCoE Blade ignore initial discovery solicitations from the CNA and go into pre-FIP mode when spanning tree is enabled. Workaround prior to upgrade:Disable the spanning tree or configure the interface as "spanning-tree edgeport". Fixed in Fabric OS 7.0.0. RASLOG message SCN-1001 severity may be misleading. Fixed in Fabric OS 7.0.0. In a FICON environment, the HP StorageWorks DC SAN Backbone Director Switch portstatsshow indicates a different value than RMF is reading through the CUP using CMD= 32 (Read port statistics). Even though the counters are updated in both cases, different values are returned for each interface. Fixed in Fabric OS 7.0.0. There are inconsistencies between WebTools and the CLI; WebTools do not show configured slots for expired trial trial slot-based licenses, but the CLI does. Fixed in Fabric OS 7.0.0. The SNMP: IF-MIB: ifTable excludes entries of port indices greater than the port index of the Logical ISL. Users will not be able to get the ports Fixed in Fabric OS 7.0.0. that have an index greater than port index of the Logical ISL. Duplicate columns are shown in WebTools port admin advanced mode when moving between basic and advanced mode. Fixed in Fabric OS 7.0.0. Executing the configdownload command without disabling the LS switch may core dump from cfgadm. Fixed in Fabric OS 7.0.0. 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
Solution
Closed fixes summary
Workaround prior to upgrade:
Users
should use the portstatsshow CLI to
find the c3 Rx and Tx timeout discards
as the porterrshow CLI will only show
the summation of many c3 discards.
Fixed in Fabric OS 7.0.0.
There is no column for discard_C3_timeout_only in porterrshow.
Fixed in Fabric OS 7.0.0.
The Port Admin window indicates Online/Healthy, yet additional port
Info indicates the port is segmented.
Fixed in Fabric OS 7.0.0.
In a FICON environment, FICON CUP cannot be enabled when a
faulted blade exists in the chassis.
Workaround prior to upgrade:
Issue
another HA Failover to cause both
CPs to reset the web services.
Fixed in Fabric OS 7.0.0.
After enabling https, a failover will cause the active CP to still be run-
ning http and users will not have https services after a failover.
Fixed in Fabric OS 7.0.0.
In Access Gateway mode, devices with QoS enabled on HBA and
F_Port and N_Port would intermittently come online without the AoQ
bit set.
Fixed in Fabric OS 7.0.0.
Removal of the HP StorageWorks B-Series Multi-protocol Router Blade
or the HP DC SAN Director 10/24 FCoE Blade could crash the HP
StorageWorks DC SAN Backbone Director Switch during POST.
Fixed in Fabric OS 7.0.0.
FAN frames are not being sent by the switch to loop devices after LIP
when fcAL.fanFrameDisable is set to 0.
Workaround prior to upgrade:
Disable
the spanning tree or configure the
interface as
“
spanning-tree edgeport
”
.
Fixed in Fabric OS 7.0.0.
The HP 2408 FCoE Switch and HP DC SAN Director 10/24 FCoE
Blade ignore initial discovery solicitations from the CNA and go into
pre-FIP mode when spanning tree is enabled.
Fixed in Fabric OS 7.0.0.
RASLOG message SCN-1001 severity may be misleading.
Fixed in Fabric OS 7.0.0.
In a FICON environment, the HP StorageWorks DC SAN Backbone
Director Switch portstatsshow indicates a different value than RMF is
reading through the CUP using CMD= 32 (Read port statistics). Even
though the counters are updated in both cases, different values are
returned for each interface.
Fixed in Fabric OS 7.0.0.
There are inconsistencies between WebTools and the CLI; WebTools
do not show configured slots for expired trial trial slot-based licenses,
but the CLI does.
Fixed in Fabric OS 7.0.0.
The SNMP: IF-MIB: ifTable excludes entries of port indices greater than
the port index of the Logical ISL. Users will not be able to get the ports
that have an index greater than port index of the Logical ISL.
Fixed in Fabric OS 7.0.0.
Duplicate columns are shown in WebTools port admin advanced mode
when moving between basic and advanced mode.
Fixed in Fabric OS 7.0.0.
Executing the configdownload command without disabling the LS
switch may core dump from cfgadm.
50