HP 4400 HP B-series Fabric OS 7.0.0a Release Notes (5697-0881, June 2011) - Page 51

StorageWorks DC SAN Backbone Director Switch in a large edge

Get HP 4400 PDF manuals and user guides View all HP 4400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Closed fixes summary An IPSec enabled FCIP circuit may bounce after running a 200 ms delay and 1% packet loss for 4 days. In Access Gateway mode, in WT-Port Admin, hitting the save button multiple times in the Edit configuration window may cause the WebLinker to crash. Solution Fixed in Fabric OS 7.0.0. Workaround prior to upgrade:Be sure to select the save button only once. Fixed in Fabric OS 7.0.0. Running system verification multiple times could cause HP DC SAN Director 10/24 FCoE Blade to fault. Fixed in Fabric OS 7.0.0. The supportshowcfgshow in supportsave does not match the output from a supportshow. Fixed in Fabric OS 7.0.0. Multiple devices lose connectivity when route is not deleted from previous trunk master after disabling and enabling the trunk. Fixed in Fabric OS 7.0.0. The HP StorageWorks DC SAN Backbone Director Switch management port speed of 1000 Mbps is displayed on WebTools as 10 Mbps. Fixed in Fabric OS 7.0.0. In a FICON environment, after IPL many FICON CHPIDs come up in Invalid Attachment state.With DCFM actively polling the fabric and reboot of the core HP StorageWorks DC SAN Backbone Director Switch in a large edge fabric, HA may go out of sync. Fixed in Fabric OS 7.0.0. With DCFM actively polling the fabric and reboot of the core HP StorageWorks DC SAN Backbone Director Switch in a large edge fabric, HA may go out of sync. Fixed in Fabric OS 7.0.0. A standby CP may experiences a software "VERIFY" error causing the CPs to lose sync.Port Auto Disable does not allow user finer granularity control over the 5 possible events for LINK DOWN that currently trigger a port being held offline. Fixed in Fabric OS 7.0.0. Port Auto Disable does not allow user finer granularity control over the 5 possible events for LINK DOWN that currently trigger a port being held offline. Fixed in Fabric OS 7.0.0. There is no functionality for querying all the IP addresses associated with the management interface of a device (both IPv4 and IPv6) over SNMP. Fixed in Fabric OS 7.0.0. Hard port faults may occur without warning messages and devices may lose their connectivity on the HP StorageWorks 4/32B SAN Switch running Fabric OS 5.3.0. Fixed in Fabric OS 7.0.0. There is no provision for adding a user configurable refresh to WebTools to decrease in the polling cycle time. Fixed in Fabric OS 7.0.0. Resets are not correctly captured in the HP StorageWorks B-series Multi-protocol Router Blade. Fixed in Fabric OS 7.0.0. "Token freed on wrong logical port" RAS message seen when cfgsave was executed. The cfgsave command does not complete in a fabric containing 6K devices. Workaround prior to upgrade:Avoid enabling the default all access with more number of devices. Fixed in Fabric OS 7.0.0. HP B-series Fabric OS 7.0.0a Release Notes 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
Solution
Closed fixes summary
Fixed in Fabric OS 7.0.0.
An IPSec enabled FCIP circuit may bounce after running a 200 ms
delay and 1% packet loss for 4 days.
Workaround prior to upgrade:
Be sure
to select the save button only once.
Fixed in Fabric OS 7.0.0.
In Access Gateway mode, in WT-Port Admin, hitting the save button
multiple times in the Edit configuration window may cause the
WebLinker to crash.
Fixed in Fabric OS 7.0.0.
Running system verification multiple times could cause HP DC SAN
Director 10/24 FCoE Blade to fault.
Fixed in Fabric OS 7.0.0.
The supportshowcfgshow in supportsave does not match the output
from a supportshow.
Fixed in Fabric OS 7.0.0.
Multiple devices lose connectivity when route is not deleted from pre-
vious trunk master after disabling and enabling the trunk.
Fixed in Fabric OS 7.0.0.
The HP StorageWorks DC SAN Backbone Director Switch management
port speed of 1000 Mbps is displayed on WebTools as 10 Mbps.
Fixed in Fabric OS 7.0.0.
In a FICON environment, after IPL many FICON CHPIDs come up in
Invalid Attachment state.With DCFM actively polling the fabric and
reboot of the core HP StorageWorks DC SAN Backbone Director
Switch in a large edge fabric, HA may go out of sync.
Fixed in Fabric OS 7.0.0.
With DCFM actively polling the fabric and reboot of the core HP
StorageWorks DC SAN Backbone Director Switch in a large edge
fabric, HA may go out of sync.
Fixed in Fabric OS 7.0.0.
A standby CP may experiences a software "VERIFY" error causing the
CPs to lose sync.Port Auto Disable does not allow user finer granularity
control over the 5 possible events for LINK DOWN that currently trigger
a port being held offline.
Fixed in Fabric OS 7.0.0.
Port Auto Disable does not allow user finer granularity control over
the 5 possible events for LINK DOWN that currently trigger a port
being held offline.
Fixed in Fabric OS 7.0.0.
There is no functionality for querying all the IP addresses associated
with the management interface of a device (both IPv4 and IPv6) over
SNMP.
Fixed in Fabric OS 7.0.0.
Hard port faults may occur without warning messages and devices
may lose their connectivity on the HP StorageWorks 4/32B SAN
Switch running Fabric OS 5.3.0.
Fixed in Fabric OS 7.0.0.
There is no provision for adding a user configurable refresh to
WebTools to decrease in the polling cycle time.
Fixed in Fabric OS 7.0.0.
Resets are not correctly captured in the HP StorageWorks B-series
Multi-protocol Router Blade.
Workaround prior to upgrade:
Avoid
enabling the default all access with
more number of devices.
Fixed in Fabric OS 7.0.0.
"Token freed on wrong logical port" RAS message seen when cfgsave
was executed. The cfgsave command does not complete in a fabric
containing 6K devices.
HP B-series Fabric OS 7.0.0a Release Notes
51