HP 6005 Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model
HP 6005 - Pro Microtower PC Manual
View all HP 6005 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP 6005 manual content summary:
- HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 1
Hardware Reference Guide HP Compaq 6005 Pro Microtower Business PC - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 2
Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. The only warranties for HP products and services . Hardware Reference Guide HP Compaq 6005 Pro Microtower Business PC First Edition (September 2009) - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 3
About This Book This guide provides basic information for upgrading this computer model. WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 4
iv About This Book ENWW - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 5
...1 Front Panel Components ...2 Media Card Reader Components ...3 Rear Panel Components ...4 Keyboard ...5 Using the Windows Logo Key 6 Serial Number Location ...7 2 Hardware Upgrades Serviceability Features ...8 Warnings and Cautions ...8 Removing the Computer Access Panel 9 Replacing the - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 6
Installing a Security Lock ...47 Cable Lock ...47 Padlock ...48 HP Business PC Security Lock 48 Front Bezel Security ...50 Appendix D Electrostatic Discharge Preventing Electrostatic Damage ...52 Grounding Methods ...52 Appendix E Computer Operating Guidelines, Routine Care and Shipping Preparation - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 7
The HP Compaq Microtower features may vary depending on the model. For a complete listing of the hardware and software installed in the computer, run the diagnostic utility (included on some computer models only). Instructions for using the utility are provided in the Troubleshooting Guide. Figure - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 8
Audio Manager icon in the Windows taskbar. NOTE: The Power On Light is normally green when the power is on. If it is flashing red, there is a problem with the computer and it is displaying a diagnostic code. Refer to the Troubleshooting Guide to interpret the code. 1 Some models have bezel blanks - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 9
I/II ● CompactFlash Card ● CompactFlash Card ● MicroDrive Type 1 Type 2 7 MS PRO/MS PRO DUO ● Memory Stick (MS) ● Memory Stick Select ● Memory Stick PRO ● MagicGate Memory Stick (MG) ● Memory Stick Duo (MS Duo) Duo (MS PRO Duo) ● Memory Stick PRO- ● MagicGate Memory ● Memory Stick PRO HG - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 10
time only if an ATI graphics card is installed in the PCI Express x16 connector. Some settings may need to be changed in Computer Setup to use both connectors. For information about setting the boot VGA controller, refer to the Computer Setup (F10) Utility Guide. 4 Chapter 1 Product Features ENWW - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 11
Page Up, Delete, End, and Page Down. 3 Status Lights Indicate the status of the computer and keyboard settings (Num Lock, Caps Lock, and Scroll Lock functions in other software applications. 8 Windows Logo Keys1 Used to open the Start menu in Microsoft Windows. Used in combination with other keys - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 12
hides the Start menu Windows Logo Key + d Displays the Desktop Windows Logo Key + m Minimizes all open applications Shift + Windows Logo Key + m Undoes Minimize All Windows Logo Key + e Launches My Computer Windows Logo Key + f Launches Find Document Windows Logo Key + Ctrl + f Launches - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 13
Serial Number Location Each computer has a unique serial number and product ID number that are located on the top cover of the computer. Keep these numbers available for use when contacting customer service for assistance. Figure 1-3 Serial Number and Product ID Location ENWW Serial Number - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 14
describes proper workstation, setup, posture, and health and work habits for computer users, and provides important electrical and mechanical safety information. This guide is located on the Web at http://www.hp.com/ergo. WARNING! Energized and moving parts inside. Disconnect power to the equipment - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 15
all removable media, such as compact discs or USB flash drives, from the computer. 3. Turn off the computer properly through the operating system, then turn off any external devices. 4. Disconnect the power cord from the power outlet and disconnect any external devices. CAUTION: Regardless of the - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 16
panel under the lip on the front of the chassis (1) then press the back end of the access panel onto the unit (2). Figure 2-2 Replacing the Computer Access Panel 2. Ensure that the panel is completely closed (1) and tighten the two thumbscrews that secure the access panel to the chassis (2). Figure - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 17
the system board as long as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage to the internal components of the computer. 5. Remove the computer access panel. 6. Lift up the three tabs on the side of the bezel (1), then rotate the bezel off the - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 18
chassis (1) then rotate the right side of the bezel onto the chassis (2) and snap it into place. Figure 2-6 Replacing the Front Bezel 12 Chapter 2 Hardware Upgrades ENWW - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 19
information In addition, the computer supports: ● 512-Mbit, 1-Gbit, and 2-Gbit non-ECC memory technologies ● single-sided and double-sided DIMMs ● DIMMs constructed with x8 and x16 DDR devices; DIMMs constructed with x4 SDRAM are not supported NOTE: The system will - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 20
XMM4. Sockets XMM1 and XMM3 operate in memory channel A. Sockets XMM2 and XMM4 operate in memory channel B. Figure 2-7 DIMM Socket Locations occupy the black XMM4 socket. Otherwise, the system will display a POST error message indicating that a memory module must be installed in the wrong socket. 14 - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 21
of the power-on state, voltage is always supplied to the memory modules as long as the computer is plugged into an active AC outlet. Adding or removing memory modules while voltage is present may cause irreparable damage to the memory modules or system board. If you see an LED light on the - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 22
access panel. 10. Reconnect the power cord and turn on the computer. 11. Lock any security devices that were disengaged when the access panel was removed. The computer should automatically recognize the additional memory the next time you turn on the computer. 16 Chapter 2 Hardware Upgrades ENWW - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 23
card: 1. Remove/disengage any security devices that prohibit opening the computer. 2. Remove all removable media, such as compact discs or USB flash drives, from the computer. 3. Turn off the computer properly through the operating system, then turn off any external devices. 4. Disconnect the power - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 24
card. a. If you are installing an expansion card in a vacant socket, remove the appropriate expansion slot cover on the back of the chassis. Pull the slot cover straight up then away from the inside of the chassis. Figure 2-11 Removing an Expansion Slot Cover 18 Chapter 2 Hardware Upgrades - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 25
from the inside of the chassis to release it from the chassis frame. Be sure not to scrape the card against the other components. Figure 2-12 Removing a Standard PCI Expansion Card c. If you are removing a PCI Express x16 card, pull the retention arm on the back of the expansion socket away from the - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 26
chassis. Press the card straight down into the expansion socket on the system board. Figure 2-14 Installing an Expansion Card NOTE: When installing an expansion card, press firmly on the card so that the whole connector seats properly in the expansion card slot. 20 Chapter 2 Hardware Upgrades ENWW - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 27
. 15. Reconnect the power cord and turn on the computer. 16. Lock any security devices that were disengaged when the access panel was removed. 17. Reconfigure the computer, if necessary. Refer to the Computer Setup (F10) Utility Guide for instructions on using Computer Setup. Drive Positions Figure - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 28
card computer may be different than the drive configuration in the illustration above. To verify the type, size, and capacity of the storage devices installed in the computer, run Computer Setup. Refer to the Computer Setup (F10) Utility Guide for more information. 22 Chapter 2 Hardware Upgrades - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 29
. Refer to the Computer Setup (F10) Utility Guide for more information. ● Connect a media card reader USB cable to the USB connector on the system board labeled MEDIA. If the media card reader has a 1394 port, connect the 1394 cable to the 1394 PCI card. ● The system does not support Parallel ATA - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 30
the operating system properly, turn off the computer, and unplug the power cord. Do not remove a drive while the computer is on or in standby mode. to liquids, temperature extremes, or products that have magnetic fields such as monitors or speakers. If a drive must be mailed, place the drive in - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 31
System Board Label 1 SATA3 2 SATA2 3 SATA1 4 SATA0 5 Media Card Reader SATA3 SATA2 SATA1 SATA0 MEDIA Color orange light blue white dark blue black NOTE: The orange SATA3 connector can be reconfigured as eSATA in the Computer Setup utility if you are installing an eSATA adapter. Select - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 32
an active AC outlet. You must disconnect the power cord to avoid damage to the internal components of the computer. 5. Remove the access panel and front power cable (1) and data cable (2) from the back of the drive. Figure 2-19 Disconnecting the Optical Drive Cables 26 Chapter 2 Hardware Upgrades - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 33
reader, disconnect the USB cable from the system board. If the media card reader has a 1394 port, disconnect the 1394 cable from the PCI card. Figure 2-20 Disconnecting the Media Card Reader USB Cable Figure 2-21 Disconnecting the Media Card Reader 1394 Cable ENWW Installing and Removing Drives 27 - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 34
bracket (1) for the drive you want to remove, then slide the drive from its drive bay (2). Figure 2-22 Removing the External Drives 8. Remove the four guide screws (two on each side) from the old drive. You will need these screws to install a new drive. 28 Chapter 2 Hardware - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 35
an active AC outlet. You must disconnect the power cord to avoid damage to the internal components of the computer. 5. If you are installing a drive in Install four M3 metric guide screws in the lower holes on each side of the drive. HP has provided eight extra M3 metric guide screws on the front - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 36
8. Slide the drive into the drive bay, making sure to align the guide screws with the guide slots, until the drive snaps into place. Figure 2-24 Sliding the External Drives into the Drive Cage 9. Connect the power and data cables to the drive as indicated in the following illustrations. a. If you - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 37
If the media card reader has a 1394 port, connect the 1394 cable to the PCI card. Figure 2-26 Connecting the Media Card Reader USB Cable Figure 2-27 Connecting the Media Card Reader 1394 Cable 10 . 11. Replace the front bezel and computer access panel. ENWW Installing and Removing Drives 31 - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 38
12. Reconnect the power cord and any external devices, then turn on the computer. 13. Lock any security devices that were disengaged when the access panel was removed. 32 Chapter 2 Hardware Upgrades ENWW - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 39
as long as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage to the internal components of the computer. 5. Remove the access panel. 6. Disconnect the power cable (1) and data cable (2) from the back of the hard drive. Figure 2-28 Disconnecting the - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 40
by pulling the release tab away from the drive (1) and sliding the drive out of the bay (2). Figure 2-29 Removing a Hard Drive 8. Remove the four guide screws (two on each side) from the old drive. You will need these screws to install a new drive. 34 Chapter 2 Hardware - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 41
board as long as the system is plugged into an active AC outlet. You must disconnect the power cord to avoid damage to the internal components of the computer. 5. Remove the access panel. 6. Install the four guide screws (two on each side) that were removed from the old drive into the new drive - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 42
to the dark blue connector labeled SATA0 to avoid any hard drive performance problems. If you are adding a second hard drive, connect the data cable Route the power and data cables in their cable retainers. 11. Replace the front bezel and computer access panel. 36 Chapter 2 Hardware Upgrades ENWW - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 43
12. Reconnect the power cord and any external devices, then turn on the computer. 13. Lock any security devices that were disengaged when the access panel was removed. Removing and Replacing a Removable 3.5-inch SATA Hard Drive Some models are - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 44
Removing the Thermal Sensor 4. Remove the four screws from the bottom of the hard drive carrier. Figure 2-35 Removing the Security Screws 38 Chapter 2 Hardware Upgrades ENWW - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 45
5. Slide the hard drive back to disconnect it from the carrier then lift it up and out of the carrier. Figure 2-36 Removing the Hard Drive 6. Place the new hard drive in the carrier then slide the hard drive back so that it seats in the SATA connector on the carrier's circuit board. Be sure the - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 46
(1) and attach the thermal sensor to the top of the hard drive with the adhesive strip (2). Figure 2-39 Replacing the Thermal Sensor 40 Chapter 2 Hardware Upgrades ENWW - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 47
to secure the cover in place (2). Figure 2-40 Replacing the Carrier Cover 10. Slide the hard drive carrier into the enclosure on the computer and lock it with the key provided. NOTE: The carrier must be locked for power to be supplied to the hard drive. ENWW Installing and Removing Drives 41 - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 48
A Specifications Table A-1 Specifications Desktop Dimensions Height 14.85 in 37.72 cm Width 6.95 Typical EPA 87/89/85% @ 20/50/100% load PS idle 238 BTU/hr 59 kg-cal/hr Power Supply 115V 230V Operating Voltage Range (STD PS)1 90-264 VAC 90-264 VAC Operating Voltage Range (EPA 87/89 - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 49
Table A-1 Specifications (continued) Power Output 320W 320W Rated Input Current (maximum)1 STD PS 5.5A @ 115 VAC 2.75A @ 230 VAC EPA 87/89/85% @ 20/50/100% load PS 5.5A @ 115 VAC 2.75A @ 230 VAC 1 This system utilizes an active power factor corrected power supply. This allows the system - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 50
only with the HP spare designated for this product. CAUTION: Before replacing the battery, it is important to back up the computer CMOS settings. When the battery is removed or replaced, the CMOS settings will be cleared. Refer to the Computer Setup (F10) Utility Guide for information on backing - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 51
NOTE: On some computer models, it may be necessary to remove an internal component to gain access to the battery. 7. Depending on the type of battery holder on the system board, complete the following instructions to replace the battery. Type 1 a. Lift the battery out of its holder. Figure B-1 - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 52
to complete this procedure. 8. Replace the computer access panel. 9. Plug in the computer and turn on power to the computer. 10. Reset the date and time, your passwords, and any special system setups using Computer Setup. Refer to the Computer Setup (F10) Utility Guide. 11. Lock any security devices - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 53
Security Devices NOTE: For information on data security features, refer to the Computer Setup (F10) Utility Guide, the Desktop Management Guide, and the HP ProtectTools Security Manager Guide (some models) at http://www.hp.com. Installing a Security Lock The security locks displayed below and on the - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 54
Padlock Figure C-2 Installing a Padlock HP Business PC Security Lock 1. Fasten the security cable by looping it around a stationary object. Figure C-3 Securing the Cable to a Fixed Object 48 Appendix C External Security Devices ENWW - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 55
2. Thread the keyboard and mouse cables through the lock. Figure C-4 Threading the Keyboard and Mouse Cables 3. Screw the lock to the chassis using the screw provided. Figure C-5 Attaching the Lock to the Chassis ENWW Installing a Security Lock 49 - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 56
screw provided by HP. To install the security screw: 1. Remove/disengage any security devices that prohibit opening the computer. 2. Remove all computer. 3. Turn off the computer properly through the operating system, then turn off any external devices. 4. Disconnect the power cord from the power - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 57
between the hard drive bay and speaker. Figure C-8 Installing the Front Bezel Security Screw 9. Replace the access panel. 10. Reconnect the power cord and turn on the computer. 11. Lock any security devices that were disengaged when the access panel was removed. ENWW Installing a Security Lock 51 - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 58
wrist strap connected by a ground cord to a grounded workstation or computer chassis. Wrist straps are flexible straps with a minimum of 1 HP authorized dealer, reseller, or service provider. NOTE: For more information on static electricity, contact an HP authorized dealer, reseller, or service - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 59
the enclosure, and the same operating guidelines listed above will still apply. ● Keep liquids away from the computer and keyboard. ● Never cover the ventilation slots on the monitor with any type of material. ● Install or enable power management functions of the operating system or other software - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 60
as condensation may form inside the unit. If the before you turn off the power. If you operate the or a soft cloth lightly moistened with a mild computer and have it checked by an authorized HP service provider. Shipping Preparation Follow these suggestions when preparing to ship the computer - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 61
removing 26 memory installing 13 populating sockets 14 specifications 13 microphone connector 2 monitor connector DisplayPort 4 VGA 4 mouse connector 4 N network connector 4 O optical drive cleaning 54 installing 29 precautions 54 removing 26 P PCI card 17, 19 PCI Express card 17, 19 power supply 42 - HP 6005 | Hardware Reference Guide - HP Compaq 6005 Pro Microtower Model - Page 62
bezel 11 hard drive 33 media card reader 26 optical drive 26 PCI card 19 PCI Express card 19 S security cable lock 47 front bezel 50 HP Business PC Security Lock 48 padlock 48 serial connector 4 serial number location 7 shipping preparation 54 specifications computer 42 memory 13 system board drive
Hardware Reference Guide
HP Compaq 6005 Pro Microtower Business PC