HP DL560 HP ProLiant DL560 Server Maintenance and Service Guide - Page 22

Hot-Plug Power Supply

Get HP DL560 - ProLiant - 1 GB RAM PDF manuals and user guides
UPC - 808736876919
View all HP DL560 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Removal and Replacement Procedures 23 CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless all bays are populated with either a component or a blank. 3. Remove the tape drive blank. a. Reach underneath and squeeze the middle of the tape drive blank (1). b. Pull the blank out of the bay (2). 4. To replace the blank, slide the blank into the bay until it locks into place. Hot-Plug Power Supply To remove the component: 1. Unlock the hinge on the cable management arm and swing the arm away from the power supply area. 2. Determine how many hot-plug power supplies are installed: − If only one hot-plug power supply is installed, power down and remove the power cord from the server ("Powering Down the Server" on page 14). − If more than one hot-plug power supply is installed, continue with the next step.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Removal and Replacement Procedures
23
CAUTION:
To prevent improper cooling and thermal damage,
do not operate the server unless all bays are populated with either a
component or a blank.
3.
Remove the tape drive blank.
a.
Reach underneath and squeeze the middle of the tape drive blank (1).
b.
Pull the blank out of the bay (2).
4.
To replace the blank, slide the blank into the bay until it locks into place.
Hot-Plug Power Supply
To remove the component:
1.
Unlock the hinge on the cable management arm and swing the arm away
from the power supply area.
2.
Determine how many hot-plug power supplies are installed:
−
If only one hot-plug power supply is installed, power down and remove
the power cord from the server ("Powering Down the Server" on page
14).
−
If more than one hot-plug power supply is installed, continue with the
next step.