HP Elite Folio 13.5 Maintenance and Service Guide - Page 43

Wireless antennas and cables (installed on top cover), IMPORTANT

Get HP Elite Folio 13.5 PDF manuals and user guides View all HP Elite Folio 13.5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

3. Remove the three Phillips M2.0 × 2.0 screws (3) that secure the touchpad to the computer. 4. Rotate the touchpad upward to a 20° to 30° angle (4), and then pull the touchpad away from the computer at an angle to remove it (5). Reverse this procedure to install the touchpad. IMPORTANT: To avoid damaging the display during touchpad installation, before inserting the touchpad into the computer, lift the top cover/keyboard up off the display. Wireless antennas and cables (installed on top cover) To remove the wireless antennas and cables that are installed on the top cover, use this procedure and illustration. Table 6-4 Wireless antennas and cables description and part number Description Spare part number Wireless antennas and cables (main) M35272-001 Wireless antennas and cables (aux) M35273-001 Before removing the wireless antennas and cables, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 28). 2. Remove the pen (see Pen on page 28). 3. Remove the bottom cover (see Bottom cover on page 30). 4. Remove the battery (see Battery on page 31). Remove the wireless antennas and cables: 1. Disconnect the antenna cables from the WLAN module (1). 2. Remove the cables from their routing under the keyboard cable and around to the left antenna (2). Component replacement procedures 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
3.
Remove the three Phillips M2.0 × 2.0 screws
(3)
that secure the touchpad to the computer.
4.
Rotate the touchpad upward to a 20° to 30° angle
(4)
, and then pull the touchpad away from the
computer at an angle to remove it
(5)
.
Reverse this procedure to install the touchpad.
IMPORTANT:
To avoid damaging the display during touchpad installation, before inserting the touchpad into
the computer, lift the top cover/keyboard up off the display.
Wireless antennas and cables (installed on top cover)
To remove the wireless antennas and cables that are installed on the top cover, use this procedure and
illustration.
Table 6-4
Wireless antennas and cables description and part number
Description
Spare part number
Wireless antennas and cables (main)
M35272-001
Wireless antennas and cables (aux)
M35273-001
Before removing the wireless antennas and cables, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
28
).
2.
Remove the pen (see
Pen
on page
28
).
3.
Remove the bottom cover (see
Bottom cover
on page
30
).
4.
Remove the battery (see
Battery
on page
31
).
Remove the wireless antennas and cables:
1.
Disconnect the antenna cables from the WLAN module
(1)
.
2.
Remove the cables from their routing under the keyboard cable and around to the left antenna
(2)
.
Component replacement procedures
35