HP Elite Folio 13.5 Maintenance and Service Guide - Page 46

Remove the Phillips M1.4 × 1.2 screw, that secures

Get HP Elite Folio 13.5 PDF manuals and user guides View all HP Elite Folio 13.5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Before removing the solid-state drive, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 28). 2. Remove the pen (see Pen on page 28). 3. Remove the bottom cover (see Bottom cover on page 30). 4. Disconnect the battery cable from the system board (see Battery on page 31). 5. Remove the heat sink (see Heat sink on page 36). Remove the solid-state drive: 1. Remove the Phillips M1.4 × 1.2 screw (1) that secures the drive to the computer. 2. Pull the drive away from the socket to remove it (2). 3. To remove the bracket from the solid-state drive, remove the Phillips M1.4 × 1.2 screw (1) that secures the bracket to the drive, and then remove the bracket from the drive (2). Install the bracket on the new solid-state drive. To install the solid-state drive, reverse the removal procedures. 38 Chapter 6 Removal and replacement procedures for authorized service provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Before removing the solid-state drive, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
28
).
2.
Remove the pen (see
Pen
on page
28
).
3.
Remove the bottom cover (see
Bottom cover
on page
30
).
4.
Disconnect the battery cable from the system board (see
Battery
on page
31
).
5.
Remove the heat sink (see
Heat sink
on page
36
).
Remove the solid-state drive:
1.
Remove the Phillips M1.4 × 1.2 screw
(1)
that secures the drive to the computer.
2.
Pull the drive away from the socket to remove it
(2)
.
3.
To remove the bracket from the solid-state drive, remove the Phillips M1.4 × 1.2 screw
(1)
that secures
the bracket to the drive, and then remove the bracket from the drive
(2)
. Install the bracket on the new
solid-state drive.
To install the solid-state drive, reverse the removal procedures.
38
Chapter 6
Removal and replacement procedures for authorized service provider parts