HP Elite Folio 13.5 Maintenance and Service Guide - Page 51

POGO connector

Get HP Elite Folio 13.5 PDF manuals and user guides View all HP Elite Folio 13.5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

4. Remove the brackets (2). 5. Remove the five Phillips M1.4 × 2.0 screws (3) that secure the system board to the computer. NOTE: If a screw is covered by protective tape, gently pull the tape up to access the screw. 6. Lift the right side of the system board up (4), and then pull the system board toward the right and out of the computer (5). Reverse this procedure to install the system board. POGO connector To remove the POGO connector, use this procedure and illustration. Table 6-9 POGO connector description and part number Description POGO connector (included in the Cable Kit) Spare part number M35257-001 Before removing the POGO connector, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 28). 2. Remove the pen (see Pen on page 28). 3. Remove the bottom cover (see Bottom cover on page 30). 4. Remove the battery (see Battery on page 31). 5. Remove the heat sink (see Heat sink on page 36). 6. Remove the solid-state drive (see Solid-state drive on page 37). Remove the POGO connector: 1. Remove the two Phillips M1.4 × 1.2 screws (1) that secure the POGO connector to the computer. Component replacement procedures 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
4.
Remove the brackets
(2)
.
5.
Remove the five Phillips M1.4 × 2.0 screws
(3)
that secure the system board to the computer.
NOTE:
If a screw is covered by protective tape, gently pull the tape up to access the screw.
6.
Lift the right side of the system board up
(4)
, and then pull the system board toward the right and out of
the computer
(5)
.
Reverse this procedure to install the system board.
POGO connector
To remove the POGO connector, use this procedure and illustration.
Table 6-9
POGO connector description and part number
Description
Spare part number
POGO connector (included in the Cable Kit)
M35257-001
Before removing the POGO connector, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
28
).
2.
Remove the pen (see
Pen
on page
28
).
3.
Remove the bottom cover (see
Bottom cover
on page
30
).
4.
Remove the battery (see
Battery
on page
31
).
5.
Remove the heat sink (see
Heat sink
on page
36
).
6.
Remove the solid-state drive (see
Solid-state drive
on page
37
).
Remove the POGO connector:
1.
Remove the two Phillips M1.4 × 1.2 screws
(1)
that secure the POGO connector to the computer.
Component replacement procedures
43