HP Elite Folio 13.5 Maintenance and Service Guide - Page 57

M35279-001 for BrightView, HP Sure View Reflect, 1000 nit panels.

Get HP Elite Folio 13.5 PDF manuals and user guides View all HP Elite Folio 13.5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

i. When replacing the display panel, install adhesive strips in the following locations on the display rear cover. NOTE: Before installing new adhesive strips, be sure to fully remove all previous adhesive remnants so the surface is clean. NOTE: New adhesive strips are provided. Use the following information to install the new adhesive on the display rear cover: - Follow the guides in the computer when installing in the display. - The release paper is white and should be faced down. - Be sure to place the right and left strips (#1 and #2) on the far edges of the display, and use the back edge of the guide to start the adhesive. - For #4 and #5 adhesives, align the cutout in the adhesive to the edge (notch) of the camera. - Press down on the strips multiple times to be sure there is good adhesion to the panel. - After all panel cables are reconnected, starting with #4 and #5, remove the top side adhesive and press the panel onto these adhesives. Then remove the side and bottom adhesives (#1, #2, #3) and press the display onto these adhesives. Similarly, after you place the panel on the adhesive strips, press down on the panel several times in the locations of the strips to be sure there is good adhesion. - Place the two rubber caps back onto the panel. NOTE: Privacy displays use unique adhesive strips on the right (2) and bottom (3) of the display. These strips are indicated by a raised P on strip as indicated in the locations in the following illustration. NOTE: After you install new adhesive strips, but before the panel is adhered to the strips, make sure that the display cable and touch board cable are reconnected and that the camera shutter is in place. You can turn on the computer to test the display before adhering the panel. Display panels are available as spare part number M35262-001 for BrightView 400 nit panels and M35279-001 for BrightView, HP Sure View Reflect, 1000 nit panels. 2. To remove the transfer board from the display rear cover: Component replacement procedures 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
i.
When replacing the display panel, install adhesive strips in the following locations on the display
rear cover.
NOTE:
Before installing new adhesive strips, be sure to fully remove all previous adhesive
remnants so the surface is clean.
NOTE:
New adhesive strips are provided. Use the following information to install the new
adhesive on the display rear cover:
- Follow the guides in the computer when installing in the display.
- The release paper is white and should be faced down.
- Be sure to place the right and left strips (#1 and #2) on the far edges of the display, and use the
back edge of the guide to start the adhesive.
- For #4 and #5 adhesives, align the cutout in the adhesive to the edge (notch) of the camera.
- Press down on the strips multiple times to be sure there is good adhesion to the panel.
- After all panel cables are reconnected, starting with #4 and #5, remove the top side adhesive and
press the panel onto these adhesives. Then remove the side and bottom adhesives (#1, #2, #3)
and press the display onto these adhesives. Similarly, after you place the panel on the adhesive
strips, press down on the panel several times in the locations of the strips to be sure there is good
adhesion.
- Place the two rubber caps back onto the panel.
NOTE:
Privacy displays use unique adhesive strips on the right
(2)
and bottom
(3)
of the display.
These strips are indicated by a raised P on strip as indicated in the locations in the following
illustration.
NOTE:
After you install new adhesive strips, but before the panel is adhered to the strips, make
sure that the display cable and touch board cable are reconnected and that the camera shutter is in
place. You can turn on the computer to test the display before adhering the panel.
Display panels are available as spare part number M35262-001 for BrightView 400 nit panels and
M35279-001 for BrightView, HP Sure View Reflect, 1000 nit panels.
2.
To remove the transfer board from the display rear cover:
Component replacement procedures
49