Home » HP Manuals » Storage Devices » HP P2000 » Manual Viewer

HP P2000 HP P2000 G3 MSA System CLI Reference Guide - Page 387

sas-status-controller-a properties continued, Table 62

View all HP P2000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 387 highlights

Table 62 sas-status-controller-a properties (continued) Name Type Description elem-status elem-statusnumeric elem-disabled elem-disablednumeric elem-reason string The SES status that corresponds to the PHY status. • Disabled: Critical condition is detected. • Error: Unrecoverable condition is detected. Appears only if there is a firmware problem related to PHY definition data. • OK: Element is installed and no error conditions are known. • Non-critical: Non-critical condition is detected. • Not Used: Element is not installed in enclosure. • Unknown: Either: • Sensor has failed or element status is not available. Appears only if an I/O module indicates it has fewer PHYs than the reporting I/O module, in which case all additional PHYs are reported as unknown. • Element is installed with no known errors, but the element has not been turned on or set into operation. string Numeric equivalents for elem-status values. • 0: Error • 1: OK • 2: Disabled • 3: Non-critical • 4: Error • 5: Not Used • 6: Unknown • 7: Unknown • 8: Unknown string • Enabled: PHY is enabled. • Disabled: PHY is disabled. string Numeric equivalents for elem-disabled values. • 0: Enabled • 1: Disabled string More information about the status value. • Blank if status is OK. • Error count interrupts: PHY disabled because of error-count interrupts. • Externally disabled: PHY disabled externally via serial debug port. • PHY control: PHY disabled by a SES control page as a result of action by a Storage Controller or user. • Not ready: PHY is enabled but not ready. Appears for SC-1 PHYs when the partner I/O module is not installed. Appears for Drive, SC-1, or Ingress PHYs when a connection problem exists such as a broken connector. • Firmware reboot • Drive removed: PHY disabled because drive slot is empty. • Unused - disabled by default: PHY is disabled by default because it is not used. • Excessive PHY changes: PHY is disabled because of excessive PHY change counts. HP P2000 G3 MSA System CLI Reference Guide 387

Section	Page
HP P2000 G3 MSA System CLI Reference Guide	1
Contents	3
Tables	9
About this guide	11
Intended audience	11
Prerequisites	11
Related documentation	11
Document conventions and symbols	12
HP technical support	12
Product warranties	13
Subscription service	13
HP web sites	13
Documentation feedback	13
Using the CLI	15
Accessing the CLI	15
CLI output formats	15
Using CLI interactively	16
Using a script to access the CLI	16
Using the XML API	18
Scripting guidelines	19
XML API examples	20
XML API optimization	20
Command syntax	21
Command names and parameters	21
Disks	21
Vdisks	22
Volumes	22
Ports	22
Command completion, editing, and history	22
Viewing help	23
Size representations	23
Event log	24
Categorical list of commands	25
Alphabetical list of commands	29
abort replication	30
abort scrub	31
abort verify	32
abort volumecopy	33
add replication-volume	34
clear cache	36
clear disk-metadata	37
clear events	39
clear expander-status	40
convert master-to-std	41
convert std-to-master	42
create chap-record	43
create host	44
create master-volume	45
create remote-system	47
create replication-set	48
create schedule	52
create snap-pool	54
create snapshots	55
create task	56
create user	59
create vdisk	61
create volume	63
create volume-copy	65
create volume-set	66
delete all-master-volumes	69
delete all-snapshots	70
delete chap-records	71
delete global-spare	72
delete host	73
delete master-volume	74
delete remote-system	75
delete replication-set	76
delete schedule	77
delete snap-pool	78
delete snapshot	79
delete snapshot-write-data	80
delete task	81
delete user	82
delete vdisks	83
delete vdisk-spare	84
delete volumes	85
dequarantine	86
detach replication-volume	88
exit	89
expand snap-pool	90
expand vdisk	91
expand volume	92
export snapshot	93
map volume	94
meta	97
ping	98
reattach replication-volume	99
remote	100
remove replication-volume	101
replicate snapshot	102
replicate volume	103
rescan	104
reset all-statistics	105
reset controller-statistics	106
reset disk-error-statistics	107
reset disk-statistics	108
reset host-link	109
reset host-port-statistics	110
reset snapshot	111
reset vdisk-statistics	112
reset volume-statistics	113
restart	114
restore defaults	115
resume replication	116
rollback master-volume	117
scrub vdisk	118
set advanced-settings	119
set auto-write-through-trigger	122
set awt	123
set cache-parameters	124
Cache write policy	125
Cache optimization mode	125
Cache read-ahead size	125
set chap-record	126
set cli-parameters	127
set controller-date	129
set debug-log-parameters	131
set disk-parameters	132
set email-parameters	133
set enclosure	134
set expander-fault-isolation	135
set expander-phy	136
set host-name	137
set host-parameters	138
set iscsi-parameters	141
set job-parameters	143
set led	144
set network-parameters	145
set ntp-parameters	147
set password	148
set priorities	149
set prompt	150
set protocols	151
set remote-system	152
set replication-external-view	153
set replication-primary-volume	154
set replication-volume-parameters	155
set schedule	157
set snap-pool-policy	158
set snap-pool-threshold	160
set snmp-parameters	161
set spares	162
set system	163
set task	164
set user	166
set vdisk	168
set volume	169
show advanced-settings	170
show auto-write-through-trigger	172
show awt	173
show cache-parameters	174
show chap-records	176
show cli-parameters	177
show configuration	179
show controller-date	180
show controllers	181
show controller-statistics	183
show debug-log-parameters	184
show disk-parameters	185
show disks	186
show disk-statistics	189
show email-parameters	190
show enclosures	191
show enclosure-status	192
show events	194
show expander-status	196
show frus	199
show host-maps	201
show host-parameters	203
show host-port-statistics	206
show hosts	207
show inquiry	208
show iscsi-parameters	209
show job-parameters	210
show license	211
show master-volumes	213
show network-parameters	215
show ntp-status	217
show ports	218
show power-supplies	220
show priorities	221
show protocols	222
show redundancy-mode	223
show refresh-counters	224
show remote-systems	225
show replication-images	226
show replication-sets	228
show replication-volumes	232
show sas-link-health	235
show schedule-details	236
show schedules	237
show sensor-status	239
show shutdown-status	241
show snap-pools	242
show snapshots	244
show snmp-parameters	246
show system	247
show system-parameters	248
show task-details	249
show tasks	254
show unwritable-cache	260
show users	261
show vdisks	262
show vdisk-statistics	264
show versions	265
show volumecopy-status	266
show volume-maps	267
show volume-names	269
show volumes	270
show volume-statistics	272
shutdown	273
start vdisk	274
stop vdisk	275
suspend replication	276
test	277
trust	278
unmap volume	279
verify links	280
verify remote-link	282
verify vdisk	283
versions	284
volumecopy	285
XML API basetype properties	287
advanced-settings-table	288
attribute-priorities	293
auto-write-through-trigger	294
cache-parameter	296
cache-settings	298
chap-records	299
cli-parameters	300
compact-flash	303
controller-cache-parameters	305
controllers	307
controller-statistics	311
debug-log-parameters	313
disk-statistics	318
drive-parameters	320
drives	322
email-parameters	327
enclosure-components	329
enclosure-fru	330
enclosure-list	332
enclosures	333
events	337
expander-ports	338
fan	340
fc-port	342
host-port-statistics	343
hosts	344
host-view	345
host-view-mappings	346
inquiry	347
iscsi-parameters	348
iscsi-port	350
job-parameters	351
license	352
log-header-table	355
master-volumes	356
network-parameters	357
ntp-status	358
policy-threshold	359
port	360
power-supplies	363
redundancy	366
refresh-counters	368
remote-addresses	370
remote-links	371
remote-system	372
replicate-volume-tasks	374
replication-image	375
replication-image-params	376
replication-set	378
replication-volume	379
replication-volume-summary	383
reset-snapshot-tasks	384
sas-port	385
sas-status-controller-a	386
schedules	389
security-communications-protocols	390
sensors	392
ses	393
shutdown-status	395
snap-pools	396
snapshots	397
snapshot-with-retention-tasks	400
snap-tasks	401
snmp-parameters	402
status	403
system	404
system-parameters-table	406
tasks	409
time-settings-table	411
unhealthy-component	412
unwritable-cache	413
users	414
vdisk-statistics	416
versions	417
virtual-disks	418
volume-copy-status	424
volume-copy-tasks	425
volume-names	426
volumes	427
volume-statistics	431
volume-view	433
volume-view-mappings	434
Settings changed by restore defaults	435
Glossary	437

Match case Limit results 1 per page

HP P2000 G3 MSA System CLI Reference Guide

387

elem-status

string

The SES status that corresponds to the PHY status.

•

Disabled

: Critical condition is detected.

•

Error

: Unrecoverable condition is detected. Appears only if there is a

firmware problem related to PHY definition data.

•

: Element is installed and no error conditions are known.

•

Non-critical

: Non-critical condition is detected.

•

Not Used

: Element is not installed in enclosure.

•

Unknown

: Either:

•

Sensor has failed or element status is not available. Appears only if an

I/O module indicates it has fewer PHYs than the reporting I/O module,

in which case all additional PHYs are reported as unknown.

•

Element is installed with no known errors, but the element has not been

turned on or set into operation.

elem-status-

numeric

string

Numeric equivalents for

elem-status

values.

•

0: Error

•

1: OK

•

2: Disabled

•

3: Non-critical

•

4: Error

•

5: Not Used

•

6: Unknown

•

7: Unknown

•

8: Unknown

elem-disabled

string

•

Enabled

: PHY is enabled.

•

Disabled

: PHY is disabled.

elem-disabled-

numeric

string

Numeric equivalents for

elem-disabled

values.

•

0: Enabled

•

1: Disabled

elem-reason

string

More information about the status value.

•

Blank if status is OK.

•

Error count interrupts

: PHY disabled because of error-count

interrupts.

•

Externally disabled

: PHY disabled externally via serial debug port.

•

PHY control

: PHY disabled by a SES control page as a result of action by

a Storage Controller or user.

•

Not ready

: PHY is enabled but not ready. Appears for SC-1 PHYs when

the partner I/O module is not installed. Appears for Drive, SC-1, or Ingress

PHYs when a connection problem exists such as a broken connector.

•

Firmware reboot

•

Drive removed

: PHY disabled because drive slot is empty.

•

Unused - disabled by default

: PHY is disabled by default because

it is not used.

•

Excessive PHY changes

: PHY is disabled because of excessive PHY

change counts.

Table 62

sas-status-controller-a properties (continued)

Name

Type

Description