HP ProLiant 4500 Compaq ProLiant 4500 Servers Maintenance and Service Guide - Page 24

Memory

Get HP ProLiant 4500 PDF manuals and user guides View all HP ProLiant 4500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

2-12 Removal and Replacement Procedures 2. Remove processor board(s). 3. Label and disconnect all cables from the backplane board. 4. Remove the Pass-Thru board. 5. Remove retaining screws (8). 6. Remove board. 7. Reverse steps to replace backplane board. Memory The ProLiant 4500 Server comes standard with 16 megabytes of system memory. Memory can be expanded to a maximum of 1.024 gigabytes by installing a matched set of four JEDEC 4-, 8-, 16-, 32-, or 64-megabyte 60-, 70-, or 80-ns industry-standard SIMM modules in the eight SIMM sockets on the system board for a total of 512 megabytes and the eight SIMM sockets on the 512-megabyte Memory Expansion Board. Figure 2-14. Removing the SIMM Module 1. Remove the side access panel. 2. Press the SIMM connector latches outward [A]. 3. Tilt the SIMM module forward [B]. 4. Lift the SIMM module out [C]. 5. To replace the SIMM module reverse these steps. IMPORTANT: Run Compaq System Configuration Utility if installed memory size has changed. A POST error message will be displayed at power up prompting you to run the System Configuration Utility. Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
2-12
Removal and Replacement Procedures
Maintenance and Service Guide
2.
Remove processor board(s).
3.
Label and disconnect all cables from the backplane board.
4.
Remove the Pass-Thru board.
5.
Remove retaining screws (8).
6.
Remove board.
7.
Reverse steps to replace backplane board.
Memory
The ProLiant 4500 Server comes standard with 16 megabytes of system memory.
Memory can be
expanded to a maximum of 1.024 gigabytes by installing a matched set of four JEDEC
4-, 8-, 16-, 32-, or 64-megabyte 60-, 70-, or 80-ns industry-standard SIMM modules in the eight
SIMM sockets on the system board for a total of 512 megabytes and the eight SIMM sockets on
the 512-megabyte Memory Expansion Board.
Figure 2-14.
Removing the SIMM Module
1.
Remove the side access panel.
2.
Press the SIMM connector latches outward [A].
3.
Tilt the SIMM module forward [B].
4.
Lift the
SIMM module out [C].
5.
To replace the SIMM module reverse these steps.
IMPORTANT:
Run Compaq System Configuration Utility if installed memory
size has changed.
A POST error message will be displayed at power up
prompting you to run the System Configuration Utility.