HP ProLiant 4500 Compaq ProLiant 4500 Servers Maintenance and Service Guide - Page 63

has invalid M&P stamp

Get HP ProLiant 4500 PDF manuals and user guides View all HP ProLiant 4500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

3-30 Diagnostic Tools Drive Monitoring features are unattainable DAAD was unable to get the monitor and performance data due to a fatal command problem such as drive time-out, or was unable to get the data due to these features not being supported on the controller. Check for other errors (time-outs, etc.). If no other errors occur, upgrade the firmware to a version that supports monitor and performance, if desired. Drive Monitoring is NOT enabled for drive bay X The monitor and performance features have not been enabled. Run the Compaq Diagnostics Utility 8.05 or higher to initialize the monitor and performance features. Drive time-out occurred on physical drive bay X DAAD issued a command to a physical drive and the command was never acknowledged. The drive or cable may be bad. Check the other error messages on the Diagnostics screen to determine resolution. Drive (bay) X firmware needs upgrading The firmware on this physical drive is below the latest recommended version. Call your Authorized Compaq Reseller to obtain the latest upgraded firmware. Drive (bay) X has invalid M&P stamp The physical drive has invalid monitor and performance data present. Run the latest Compaq Diagnostics Utility to properly initialize this drive. Drive X indicates position Y This message indicates which physical drive appears to be scrambled or in the wrong drive bay that it was originally configured for. Examine the graphical drive representation on DAAD to determine proper drive locations. Remove drive X and place it in drive position Y. Rearrange the drives according to the DAAD instructions. Drive (bay) X RIS copy mismatch The copies of the RIS on this drive do not match. This drive may need to be replaced. Check for other errors. Drive (bay) X upload code not readable An error occurred while DAAD was trying to read the upload code information from this drive. If there were multiple errors, this drive may need to be replaced. Duplicate write memory error Data could not be written to the array accelerator board in duplicate due to the detection of parity errors. This is not a data loss situation. Replace the array accelerator board. Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
3-30
Diagnostic Tools
Maintenance and Service Guide
Drive Monitoring features are unattainable
DAAD was unable to get the monitor and performance data due to a fatal command problem
such as drive time-out, or was unable to get the data due to these features not being supported
on the controller.
Check for other errors (time-outs, etc.). If no other errors occur, upgrade the firmware to a
version that supports monitor and performance, if desired.
Drive Monitoring is NOT enabled for drive bay
X
The monitor and performance features have not been enabled.
Run the Compaq Diagnostics Utility 8.05 or higher to initialize the monitor and
performance features.
Drive time-out occurred on physical drive bay
X
DAAD issued a command to a physical drive and the command was never acknowledged.
The drive or cable may be bad. Check the other error messages on the Diagnostics screen to
determine resolution.
Drive (bay)
X
firmware needs upgrading
The firmware on this physical drive is below the latest recommended version.
Call your Authorized Compaq Reseller to obtain the latest upgraded firmware.
Drive (bay)
X
has invalid M&P stamp
The physical drive has invalid monitor and performance data present.
Run the latest Compaq Diagnostics Utility to properly initialize this drive.
Drive
X
indicates position
Y
This message indicates which physical drive appears to be scrambled or in the wrong drive
bay that it was originally configured for.
Examine the graphical drive representation on DAAD to determine proper drive locations.
Remove drive X and place it in drive position Y. Rearrange the drives according to the
DAAD instructions.
Drive (bay)
X
RIS copy mismatch
The copies of the RIS on this drive do not match.
This drive may need to be replaced. Check for other errors.
Drive (bay)
X
upload code not readable
An error occurred while DAAD was trying to read the upload code information from this
drive.
If there were multiple errors, this drive may need to be replaced.
Duplicate write memory error
Data could not be written to the array accelerator board in duplicate due to the detection of
parity errors. This is
not
a data loss situation.
Replace the array accelerator board.