HP ProLiant 4500 Compaq ProLiant 4500 Servers Maintenance and Service Guide - Page 61

Configuration signature is zero

Get HP ProLiant 4500 PDF manuals and user guides View all HP ProLiant 4500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

3-28 Diagnostic Tools Battery X not fully charged The battery is not fully charged. If 75% of the batteries present are fully charged, the array accelerator is fully operational. If more than 75% of the batteries are not fully charged, allow 36 hours to recharge them. Board not attached The IDA-2 board has been configured for use with an array accelerator board, but one is currently not attached. Locate the original array accelerator board and attach it to the IDA-2 board. CMOS present, controller not detected EISA nonvolatile RAM has a configuration for an array controller but there is no board in this slot. Either a board has been removed from the system or a board has been placed in the wrong slot. Place the array controller in the proper slot or run the System Configuration Utility to reconfigure nonvolatile RAM to reflect the removal or new position. Compatibility port problem detected You have the compatibility port configured for this IDA controller. When DAAD was verifying this interface, a serious problem was detected. A hardware problem has occurred and you should replace the IDA controller. Configuration signature is zero DAAD detected that nonvolatile RAM contains a configuration signature that is zero. Old versions of the System Configuration Utility could cause this. Run the latest version of System Configuration Utility to configure the controller and nonvolatile RAM. Configuration signature mismatch The array accelerator board has been configured for a different IDA-2 board. The configuration signature on the array accelerator board does not match the one stored on the IDA-2 board. To recognize the array accelerator board, run the System Configuration Utility. Controller communication failure occurred DAAD was unable to successfully issue commands to the controller in this slot. Controller detected. CMOS not present The EISA nonvolatile RAM is not configured. Run the System Configuration Utility to configure the nonvolatile RAM. Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
3-28
Diagnostic Tools
Maintenance and Service Guide
Battery
X
not fully charged
The battery is not fully charged.
If 75% of the batteries present are fully charged, the array accelerator is fully operational. If
more than 75% of the batteries are
not
fully charged, allow 36 hours to recharge them.
Board not attached
The IDA-2 board has been configured for use with an array accelerator board, but one is
currently not attached.
Locate the original array accelerator board and attach it to the IDA-2 board.
CMOS present, controller not detected
EISA nonvolatile RAM has a configuration for an array controller but there is no board in this
slot. Either a board has been removed from the system or a board has been placed in the
wrong slot.
Place the array controller in the proper slot or run the System Configuration Utility to re-
configure nonvolatile RAM to reflect the removal or new position.
Compatibility port problem detected
You have the compatibility port configured for this IDA controller. When DAAD was
verifying this interface, a serious problem was detected.
A hardware problem has occurred and you should replace the IDA controller.
Configuration signature is zero
DAAD detected that nonvolatile RAM contains a configuration signature that is zero. Old
versions of the System Configuration Utility could cause this.
Run the latest version of System Configuration Utility to configure the controller and
nonvolatile RAM.
Configuration signature mismatch
The array accelerator board has been configured for a different IDA-2 board. The
configuration signature on the array accelerator board does not match the one stored on the
IDA-2 board.
To recognize the array accelerator board, run the System Configuration Utility.
Controller communication failure occurred
DAAD was unable to successfully issue commands to the controller in this slot.
Controller detected. CMOS not present
The EISA nonvolatile RAM is not configured.
Run the System Configuration Utility to configure the nonvolatile RAM.