Hitachi C10RA3 Instruction Manual - Page 20

Using Wood Facing On The Rip Fence

Get Hitachi C10RA3 - 10 Inch Portable Table Saw PDF manuals and user guides
UPC - 717709011038
View all Hitachi C10RA3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

English COMPOUND MITER CROSSCUTTING (FIG. FF) This sawing operation is combining a miter angle with a bevel angle. WARNING Always work to the right side of the blade during this type of cut. The miter gauge (3) must be in the right side groove because the bevel angle may cause the blade guard to interfere with the cut if used on the left side groove. When tilting the workpiece to 45° and push it toward the blade, the blade guard may hit the blade. To avoid injury, stop the work at that time. 1. Set the miter gauge (3) to the desired angle. 2. Place the miter gauge (3) in the right side groove (2) of the table. 3. Set the blade (1) bevel to the desired bevel angle and tighten the blade bevel lock knob. 4. Hold workpiece firmly against the face of the miter gauge (3) throughout the cutting operation. Fig. FF 12 3 MITER CUTS (FIG. GG) This sawing operation is the same as crosscutting except the miter gauge is locked at an angle other than 90°. 1. Set the blade (1) to 0° bevel angle and tighten the blade bevel lock knob. 2. Set the miter gauge (3) at the desired miter angle and lock in position by tightening the miter gauge locking handle. 3. Hold the workpiece (2) firmly against the face of the miter gauge throughout the cutting operation. Fig. GG 3 2 1 USING WOOD FACING ON THE RIP FENCE (FIG. HH) When performing some special cutting operations, add a wood facing (1) to either side of the rip fence (2). 1. Use a smooth & straight 3/4 in thick wood board (1) that is as long as the rip fence. 2. Attach the wood facing to the fence with wood screws (3) through the holes in the fence. A wood fence should be used when ripping material such as thin paneling to prevent the material from catching between the bottom of the fence and the table. Fig. HH 3 2 1 AUXILIARY FENCE (FIG. II) Making the base: • Start with a piece of 3/8 in plywood at least 5-1/2 in wide or wider and 30 in long or longer. • Cut the piece to shape and size shown: Making the side: • Start with a piece of 3/4 in plywood at least 2-3/8 in wide or wider and 27 in long or longer • Cut the piece to shape and size shown: Putting it together: • Put the pieces together, as shown: WARNING Make sure the screw heads do not stick out from the bottom of the base, they must be flush or recessed. The bottom must be flat and smooth enough to rest on the saw table without rocking. 3-1/2" Fig. II 30" 2-5/8" 3/8" Thick plywood base 27" 3/4" Thick plywood side 5-1/2" 4-3/4" 1-1/4" 2-3/8" - 20 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
– 20 –
English
USING WOOD FACING ON THE RIP FENCE
(FIG. HH)
When performing some special cutting operations, add
a wood facing (1) to either side of the rip fence (2).
1. Use a smooth & straight 3/4 in thick wood board
(1) that is as long as the rip fence.
2. Attach the wood facing to the fence with wood
screws (3) through the holes in the fence. A wood
fence should be used when ripping material such as
thin paneling to prevent the material from catching
between the bottom of the fence and the table.
Fig.
HH
AUXILIARY FENCE (FIG. II)
Making the base:
•
Start with a piece of 3/8 in plywood at least 5-1/2 in
wide or wider and 30 in long or longer.
•
Cut the piece to shape and size shown:
Making the side:
•
Start with a piece of 3/4 in plywood at least 2-3/8 in
wide or wider and 27 in long or longer
•
Cut the piece to shape and size shown:
Putting it together:
•
Put the pieces together, as shown:
Make sure the screw heads do not stick out from the
bottom of the base, they must be flush or recessed.
The bottom must be flat and smooth enough to rest
on the saw table without rocking.
Fig.
II
COMPOUND MITER CROSSCUTTING (FIG. FF)
This sawing operation is combining a miter angle with a
bevel angle.
Always work to the right side of the blade during this
type of cut. The miter gauge (3) must be in the right
side groove because the bevel angle may cause the
blade guard to interfere with the cut if used on the
left side groove.
When tilting the workpiece to 45° and push it toward
the blade, the blade guard may hit the blade. To
avoid injury, stop the
work at that time.
1. Set the miter gauge (3) to the desired angle.
2. Place the miter gauge (3) in the right side groove (2)
of the table.
3. Set the blade (1) bevel to the desired bevel angle
and tighten the blade bevel lock knob.
4. Hold workpiece firmly against the face of the miter
gauge (3) throughout the cutting operation.
Fig.
FF
MITER CUTS (FIG.
GG)
This sawing operation is the same as crosscutting
except the miter gauge is locked at an angle other
than 90°.
1. Set the blade (1) to 0° bevel angle and tighten the
blade bevel lock knob.
2. Set the miter gauge (3) at the desired miter angle and
lock in position by tightening the miter gauge locking
handle.
3. Hold the workpiece (2) firmly against the face of the
miter gauge throughout the cutting operation.
Fig.
GG
WARNING
WARNING
3
2
1
30”
2-5/8”
3-1/2”
3/8” Thick plywood base
27”
3/4” Thick plywood
side
5-1/2”
2-3/8”
4-3/4”
1-1/4”
1
1
2
3
1
2
3