Intel BOXD955XCSLKR Product Specification - Page 25

Auxiliary Power AUX PWR Connector Optional, 9 IEEE-1394a/b Connectors Optional

Get Intel BOXD955XCSLKR - Motherboard 955X Express Chipset BTX PDF manuals and user guides
UPC - 735858173834
View all Intel BOXD955XCSLKR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Product Description 1.8 Auxiliary Power (AUX PWR) Connector (Optional) The board includes a 1x4 power connector that can be used to provide power for internal chassis lighting or additional fans. The on/off function of this connector is controlled from within the BIOS Setup Program. The default setting in the BIOS is for this connector to be off. CAUTION When using this connector, observe the following precautions: • This connector does not include overcurrent protection. Do not connect any devices to this connector that draw more than 1.5 A. • This connector will not provide adequate power for storage devices. Do not use a Y-adapter, power splitter, or SATA power adapter to attach storage devices (such as hard disk drives or CD/DVD drives) to this connector. Failure to observe these precautions may cause damage to the board. For information about The location of the optional auxiliary power connector The signal names of the optional auxiliary power connector Refer to Figure 19, page 54 Table 24, page 57 1.9 IEEE-1394a/b Connectors (Optional) The optional IEEE-1394 interface addresses interconnection of both computer peripherals and consumer electronics with these features: • IEEE-1394a and IEEE-1394b operation • Support for up to 63 peer-to-peer devices • Operation ranging from 100 Mbits/sec to 800 Mbits/sec (depending on cable type) • Connection over short and long distances • Support for both asynchronous and isochronous data transfer As a manufacturing option, the board includes three IEEE-1394a/b connectors as follows: • One IEEE-1394a connector located on the back panel. This connector supports IEEE-1394a operation only; IEEE-1394b operation is not supported. • Two IEEE-1394a/b front-panel connectors located on the component side. These connectors can be independently configured for either IEEE-1394a or IEEE-1394b operation using the BIOS Setup program. The IEEE-1394a interface provides a throughput ranging from 100 Mbits/sec to 400 Mbits/sec. The IEEE-1394b interface is completely compatible with IEEE-1394a. IEEE-1394b also supports higher data transfer rates (800 Mbits/sec) and longer distances. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Product Description
25
1.8 Auxiliary Power (AUX PWR) Connector (Optional)
The board includes a 1x4 power connector that can be used to provide power for internal chassis
lighting or additional fans.
The on/off function of this connector is controlled from within the
BIOS Setup Program.
The default setting in the BIOS is for this connector to be off.
CAUTION
When using this connector, observe the following precautions:
•
This connector does not include overcurrent protection.
Do not connect any devices to this
connector that draw more than 1.5 A.
•
This connector will not provide adequate power for storage devices.
Do not use a Y-adapter,
power splitter, or SATA power adapter to attach storage devices (such as hard disk drives or
CD/DVD drives) to this connector.
Failure to observe these precautions may cause damage to the board.
For information about
Refer to
The location of the optional auxiliary power connector
Figure 19, page 54
The signal names of the optional auxiliary power connector
Table 24, page 57
1.9 IEEE-1394a/b Connectors (Optional)
The optional IEEE-1394 interface addresses interconnection of both computer peripherals and
consumer electronics with these features:
•
IEEE-1394a and IEEE-1394b operation
•
Support for up to 63 peer-to-peer devices
•
Operation ranging from 100 Mbits/sec to 800 Mbits/sec (depending on cable type)
•
Connection over short and long distances
•
Support for both asynchronous and isochronous data transfer
As a manufacturing option, the board includes three IEEE-1394a/b connectors as follows:
•
One IEEE-1394a connector located on the back panel.
This connector supports IEEE-1394a
operation only; IEEE-1394b operation is not supported.
•
Two IEEE-1394a/b front-panel connectors located on the component side.
These connectors
can be independently configured for either IEEE-1394a or IEEE-1394b operation using the
BIOS Setup program.
The IEEE-1394a interface provides a throughput ranging from 100 Mbits/sec to 400 Mbits/sec.
The IEEE-1394b interface is completely compatible with IEEE-1394a.
IEEE-1394b also supports
higher data transfer rates (800 Mbits/sec) and longer distances.