Home » Intel Manuals » Motherboards » Intel D915GAG » Manual Viewer

Intel D915GAG Product Specification - Page 72

Power Supply Connectors, INTEGRATOR'S NOTE

Get Intel D915GAG PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Intel Desktop Board D915GAV/D915GAG Technical Product Specification 2.8.2.2 Power Supply Connectors The board has three power supply connectors: • Main power - a 2 x 12 connector. This connector is compatible with 2 x 10 connectors previously used on Intel Desktop boards. The board supports the use of ATX12V power supplies with either 2 x 10 or 2 x 12 main power cables. When using a power supply with a 2 x 10 main power cable, attach that cable on the rightmost pins of the main power connector, leaving pins 11, 12, 23, and 24 unconnected. • ATX12V power - a 2 x 2 connector. This connector provides power directly to the processor voltage regulator and must always be used. Failure to do so will prevent the board from booting. • Alternate power - a 1 x 4 connector. This connector provides additional power when using high wattage PCI Express x16 graphics cards. # INTEGRATOR'S NOTE When using high wattage PCI Express x16 graphics cards, use one of the following power supply configurations to avoid system instability: • The preferred method of power delivery is to use a power supply with a 2 x 12 main power cable. In this configuration, use two connectors to provide power to the board: ⎯ The main power connector ⎯ The ATX12V connector In this configuration, the alternate power connector is not required. The 2 x 12 main power cable can provide up to 144 W of power from the +12 V rail. • An alternate method of power delivery is to use a power supply has a 2 x 10 main power cable. In this configuration, use three connectors to provide power to the board: ⎯ The main power connector ⎯ The ATX12V connector ⎯ The alternate power connector Table 31. Main Power Connector Pin Signal Name 1 +3.3 V 2 +3.3 V 3 Ground 4 +5 V 5 Ground 6 +5 V 7 Ground 8 PWRGD (Power Good) 9 +5 V (Standby) 10 +12 V 11 +12 V (Note) 12 2 x 12 connector detect (Note) Pin Signal Name 13 +3.3 V 14 -12 V 15 Ground 16 PS-ON# (power supply remote on/off) 17 Ground 18 Ground 19 Ground 20 No connect 21 +5 V 22 +5 V 23 +5 V (Note) 24 Ground (Note) Note: When using a 2 x 10 power supply cable, this pin will be unconnected. 72

Section	Page
Intel® Desktop Boards D915GAV/D915GAG Technical Product Specification	1
Revision History	2
Preface	3
Intended Audience	3
What This Document Contains	3
Typographical Conventions	3
Other Common Notations	4
Contents	5
1 Product Description	11
1.1 PCI Bus Terminology Change	11
1.2 Board Differences	11
1.3 Overview	12
1.3.1 Feature Summary	12
1.3.2 Manufacturing Options	13
1.3.3 Board Layouts	14
1.3.4 Block Diagram	18
1.4 Online Support	19
1.5 Processor	19
1.6 System Memory	20
1.6.1 Memory Configurations	22
1.7 Intel® 915G Chipset	26
1.7.1 Intel 915G Graphics Subsystem	26
1.7.2 USB	28
1.7.3 IDE Support	28
1.7.4 Real-Time Clock, CMOS SRAM, and Battery	30
1.8 PCI Express Connectors	30
1.9 I/O Controller	31
1.9.1 Serial Ports	31
1.9.2 Parallel Port	31
1.9.3 Diskette Drive Controller	32
1.9.4 Keyboard and Mouse Interface	32
1.10 Audio Subsystem	32
1.10.1 Audio Subsystem Software	33
1.10.2 Audio Connectors	33
1.10.3 Intel High Definition Audio Subsystem	34
1.11 LAN Subsystem	35
1.11.1 10/100 Mbits/sec LAN Subsystem	35
1.11.2 Gigabit LAN Subsystem	36
1.11.3 Alert Standard Format (ASF) Support	37
1.11.4 LAN Subsystem Software	38
1.12 Hardware Management Subsystem	38
1.12.1 Hardware Monitoring and Fan Control ASIC	38
1.12.2 Thermal Monitoring	39
1.12.3 Fan Monitoring	41
1.12.4 Chassis Intrusion and Detection	41
1.13 Power Management	41
1.13.1 ACPI	41
1.13.2 Hardware Support	44
1.14 Trusted Platform Module (Optional)	48
1.14.1 System Requirements	48
1.14.2 Warning of Potential Data Loss	48
1.14.3 Security Precautions	49
1.14.4 Trusted Platform Module Ownership	50
1.14.5 Enabling the Trusted Platform Module	51
1.14.6 Assuming Trusted Platform Module Ownership	51
1.14.7 Recovery Procedures	52
1.14.8 Clearing Trusted Platform Module Ownership	53
1.14.9 Software Support	54
2 Technical Reference	55
2.1 Introduction	55
2.2 Memory Resources	55
2.2.1 Addressable Memory	55
2.2.2 Memory Map	57
2.3 DMA Channels	57
2.4 Fixed I/O Map	58
2.5 PCI Configuration Space Map	59
2.6 Interrupts	60
2.7 PCI Conventional Interrupt Routing Map	61
2.8 Connectors	63
2.8.1 Back Panel Connectors	64
2.8.2 Component-side Connectors	66
2.9 Jumper Block	77
2.10 Mechanical Considerations	78
2.10.1 D915GAV Board Form Factor	78
2.10.2 D915GAG Board Form Factor	79
2.10.3 I/O Shield	80
2.11 Electrical Considerations	81
2.11.1 DC Loading	81
2.11.2 Add-in Board Considerations	81
2.11.3 Fan Connector Current Capability	82
2.11.4 Power Supply Considerations	82
2.12 Thermal Considerations	83
2.13 Reliability	85
2.14 Environmental	86
2.15 Regulatory Compliance	87
2.15.1 Safety Regulations	87
2.15.2 EMC Regulations	87
2.15.3 European Union Declaration of Conformity Statement	88
2.15.4 Product Ecology Statements	89
2.15.5 Product Certification Markings (Board Level)	90
3 Overview of BIOS Features	91
3.1 Introduction	91
3.2 BIOS Flash Memory Organization	92
3.3 Resource Configuration	92
3.3.1 PCI Autoconfiguration	92
3.3.2 PCI IDE Support	92
3.4 System Management BIOS (SMBIOS)	93
3.5 Legacy USB Support	93
3.6 BIOS Updates	94
3.6.1 Language Support	94
3.6.2 Custom Splash Screen	94
3.7 Boot Options	95
3.7.1 CD-ROM Boot	95
3.7.2 Network Boot	95
3.7.3 Booting Without Attached Devices	95
3.7.4 Changing the Default Boot Device During POST	95
3.8 Fast Booting Systems with Intel Rapid BIOS Boot	96
3.8.1 Peripheral Selection and Configuration	96
3.8.2 Intel Rapid BIOS Boot	96
3.9 BIOS Security Features	97
4 Error Messages and Beep Codes	99
4.1 BIOS Error Messages	99
4.2 Port 80h POST Codes	101
4.3 Bus Initialization Checkpoints	105
4.4 Speaker	106