Home » Intel Manuals » Motherboards » Intel D925XECV2 » Manual Viewer

Intel D925XECV2 Product Specification - Page 44

Power Connector, 14.2.2, Fan Connectors, 14.2.3, LAN Wake Capabilities, CAUTION - boot from usb

Get Intel D925XECV2 PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Intel Desktop Boards D925XECV2/D925XEBC2 Technical Product Specification Resume on Ring enables telephony devices to access the computer when it is in a power-managed state. The method used depends on the type of telephony device (external or internal). NOTE The use of Resume on Ring and Wake from USB technologies from an ACPI state requires an operating system that provides full ACPI support. 1.14.2.1 Power Connector ATX12V-compliant power supplies can turn off the system power through system control. When an ACPI-enabled system receives the correct command, the power supply removes all non-standby voltages. When resuming from an AC power failure, the computer returns to the power state it was in before power was interrupted (on or off). The computer's response can be set using the Last Power State feature in the BIOS Setup program's Boot menu. For information about The location of the power connector The signal names of the power connector Refer to Figure 21, page 68 Table 29, page 75 1.14.2.2 Fan Connectors The function/operation of the fan connectors is as follows: • The fans are on when the board is in the S0 or S1 state. • The fans are off when the board is off or in the S3, S4, or S5 state. • Each fan connector is wired to a fan tachometer input of the hardware monitoring and fan control ASIC • All fan connectors support closed-loop fan control that can adjust the fan speed or switch the fan on or off as needed. • All fan connectors have a +12 V DC connection For information about The location of the fan connectors The location of the fan connectors and sensors for thermal monitoring The signal names of the fan connectors Refer to Figure 21, page 68 Figure 15, page 38 Section 2.8.1.1, page 64 1.14.2.3 LAN Wake Capabilities CAUTION For LAN wake capabilities, the +5 V standby line for the power supply must be capable of providing adequate +5 V standby current. Failure to provide adequate standby current when implementing LAN wake capabilities can damage the power supply. LAN wake capabilities enable remote wake-up of the computer through a network. The LAN network adapter monitors network traffic at the Media Independent Interface. Upon detecting a Magic Packet* frame, the LAN subsystem asserts a wake-up signal that powers up the computer. 44

Section	Page
Intel® Desktop Boards D925XECV2/D925XEBC2 Technical Product Specification	1
Revision History / Disclaimer	2
Preface	3
Intended Audience	3
What This Document Contains	3
Typographical Conventions	3
Other Common Notation	4
Contents	5
1 Product Description	11
1.1 PCI Bus Terminology Change	11
1.2 Board Differences	11
1.3 Overview	12
1.3.1 Feature Summary	12
1.3.2 Manufacturing Options	13
1.3.3 Board Layouts	14
1.3.4 Block Diagram	18
1.4 Online Support	19
1.5 Processor	19
1.6 System Memory	20
1.6.1 Memory Configurations	21
1.7 Intel® 925XE Chipset	25
1.7.1 USB	25
1.7.2 IDE Support	25
1.7.3 Real-Time Clock, CMOS SRAM, and Battery	28
1.8 PCI Express Connectors	28
1.9 Auxiliary Power (AUX PWR) Output Connector	28
1.10 I/O Controller	29
1.10.1 Serial Port	29
1.10.2 Parallel Port	29
1.10.3 Diskette Drive Controller	30
1.10.4 Keyboard and Mouse Interface	30
1.11 Audio Subsystem	31
1.11.1 Audio Subsystem Software	31
1.11.2 Audio Connectors	31
1.11.3 8-Channel (7.1) Audio Subsystem	32
1.11.4 6-Channel (5.1) Audio Subsystem	34
1.12 LAN Subsystem	35
1.12.1 Marvell Yukon 88E8050 PCI Express 1.0a Integrated MAC/PHY Gigabit Ethernet Controller	35
1.12.2 RJ-45 LAN Connector with Integrated LEDs	35
1.12.3 Alert Standard Format (ASF) Support	36
1.12.4 LAN Subsystem Software	36
1.13 Hardware Management Subsystem	37
1.13.1 Hardware Monitoring and Fan Control ASIC	37
1.13.2 Thermal Monitoring	38
1.13.3 Fan Monitoring	40
1.13.4 Chassis Intrusion and Detection	40
1.14 Power Management	40
1.14.1 ACPI	40
1.14.2 Hardware Support	43
1.15 Trusted Platform Module (Optional)	47
1.15.1 System Requirements	47
1.15.2 Warning of Potential Data Loss	47
1.15.3 Security Precautions	48
1.15.4 Trusted Platform Module Ownership	49
1.15.5 Enabling the Trusted Platform Module	50
1.15.6 Assuming Trusted Platform Module Ownership	50
1.15.7 Recovery Procedures	51
1.15.8 Clearing Trusted Platform Module Ownership	52
1.15.9 Software Support	53
2 Technical Reference	55
2.1 Introduction	55
2.2 Memory Resources	55
2.2.1 Addressable Memory	55
2.2.2 Memory Map	57
2.3 DMA Channels	57
2.4 Fixed I/O Map	58
2.5 PCI Configuration Space Map	59
2.6 Interrupts	60
2.7 PCI Conventional Interrupt Routing Map	61
2.8 Connectors	63
2.8.1 Back Panel Connectors	63
2.8.2 Component-side Connectors	68
2.9 Jumper Block	80
2.10 Mechanical Considerations	81
2.10.1 D925XECV2 Form Factor	81
2.10.2 D925XEBC2 Form Factor	82
2.10.3 I/O Shield	83
2.11 Electrical Considerations	85
2.11.1 DC Loading	85
2.11.2 Add-in Board Considerations	85
2.11.3 Fan Connector Current Capability	86
2.11.4 Power Supply Considerations	86
2.12 Thermal Considerations	87
2.13 Reliability	89
2.14 Environmental	90
2.15 Regulatory Compliance	91
2.15.1 Safety Regulations	91
2.15.2 EMC Regulations	91
2.15.3 European Union Declaration of Conformity Statement	92
2.15.4 Product Ecology Statements	93
2.15.5 Product Certification Markings (Board Level)	94
3 Overview of BIOS Features	95
3.1 Introduction	95
3.2 BIOS Flash Memory Organization	96
3.3 Resource Configuration	96
3.3.1 PCI Autoconfiguration	96
3.3.2 PCI IDE Support	96
3.4 System Management BIOS (SMBIOS)	97
3.5 Legacy USB Support	97
3.6 BIOS Updates	98
3.6.1 Language Support	98
3.6.2 Custom Splash Screen	98
3.7 Boot Options	99
3.7.1 CD-ROM Boot	99
3.7.2 Network Boot	99
3.7.3 Booting Without Attached Devices	99
3.7.4 Changing the Default Boot Device During POST	99
3.8 Fast Booting Systems with Intel® Rapid BIOS Boot	100
3.8.1 Peripheral Selection and Configuration	100
3.8.2 Intel Rapid BIOS Boot	100
3.9 BIOS Security Features	101
4 Error Messages and Beep Codes	103
4.1 BIOS Error Messages	103
4.2 Port 80h POST Codes	105
4.3 Bus Initialization Checkpoints	109
4.4 Speaker	110

Match case Limit results 1 per page

Intel Desktop Boards D925XECV2/D925XEBC2 Technical Product Specification

Resume on Ring enables telephony devices to access the computer when it is in a power-managed

state.

The method used depends on the type of telephony device (external or internal).

NOTE

The use of Resume on Ring and Wake from USB technologies from an ACPI state requires an

operating system that provides full ACPI support.

1.14.2.1

Power Connector

ATX12V-compliant power supplies can turn off the system power through system control.

When

an ACPI-enabled system receives the correct command, the power supply removes all non-standby

voltages.

When resuming from an AC power failure, the computer returns to the power state it was in before

power was interrupted (on or off).

The computer’s response can be set using the Last Power State

feature in the BIOS Setup program’s Boot menu.

For information about

Refer to

The location of the power connector

Figure 21, page 68

The signal names of the power connector

Table 29, page 75

1.14.2.2

Fan Connectors

The function/operation of the fan connectors is as follows:

•

The fans are on when the board is in the S0 or S1 state.

•

The fans are off when the board is off or in the S3, S4, or S5 state.

•

Each fan connector is wired to a fan tachometer input of the hardware monitoring and fan

control ASIC

•

All fan connectors support closed-loop fan control that can adjust the fan speed or switch the

fan on or off as needed.

•

All fan connectors have a +12 V DC connection

For information about

Refer to

The location of the fan connectors

Figure 21, page 68

The location of the fan connectors and sensors for thermal monitoring

Figure 15, page 38

The signal names of the fan connectors

Section 2.8.1.1, page 64

1.14.2.3

LAN Wake Capabilities

CAUTION

For LAN wake capabilities, the +5 V standby line for the power supply must be capable of

providing adequate +5 V standby current.

Failure to provide adequate standby current when

implementing LAN wake capabilities can damage the power supply.

LAN wake capabilities enable remote wake-up of the computer through a network.

The LAN

network adapter monitors network traffic at the Media Independent Interface.

Upon detecting a

Magic Packet* frame, the LAN subsystem asserts a wake-up signal that powers up the computer.