Home » Intel Manuals » Motherboards » Intel D925XECV2 » Manual Viewer

Intel D925XECV2 Product Specification - Page 46

WAKE# Signal Wake-up Support, 14.2.10, 5 V Standby Power Indicator LED, CAUTION

Get Intel D925XECV2 PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Intel Desktop Boards D925XECV2/D925XEBC2 Technical Product Specification 1.14.2.9 WAKE# Signal Wake-up Support When the WAKE# signal on the PCI Express bus is asserted, the computer wakes from an ACPI S1, S3, S4, or S5 state. 1.14.2.10 +5 V Standby Power Indicator LED The +5 V standby power indicator LED shows that power is still present even when the computer appears to be off. Figure 17 shows the location of the standby power indicator LED on the D925XECV2 board. CAUTION If AC power has been switched off and the standby power indicator is still lit, disconnect the power cord before installing or removing any devices connected to the board. Failure to do so could damage the board and any attached devices. CR3J1 OM16678 Figure 17. Location of the Standby Power Indicator LED on the D925XECV2 Board 46

Section	Page
Intel® Desktop Boards D925XECV2/D925XEBC2 Technical Product Specification	1
Revision History / Disclaimer	2
Preface	3
Intended Audience	3
What This Document Contains	3
Typographical Conventions	3
Other Common Notation	4
Contents	5
1 Product Description	11
1.1 PCI Bus Terminology Change	11
1.2 Board Differences	11
1.3 Overview	12
1.3.1 Feature Summary	12
1.3.2 Manufacturing Options	13
1.3.3 Board Layouts	14
1.3.4 Block Diagram	18
1.4 Online Support	19
1.5 Processor	19
1.6 System Memory	20
1.6.1 Memory Configurations	21
1.7 Intel® 925XE Chipset	25
1.7.1 USB	25
1.7.2 IDE Support	25
1.7.3 Real-Time Clock, CMOS SRAM, and Battery	28
1.8 PCI Express Connectors	28
1.9 Auxiliary Power (AUX PWR) Output Connector	28
1.10 I/O Controller	29
1.10.1 Serial Port	29
1.10.2 Parallel Port	29
1.10.3 Diskette Drive Controller	30
1.10.4 Keyboard and Mouse Interface	30
1.11 Audio Subsystem	31
1.11.1 Audio Subsystem Software	31
1.11.2 Audio Connectors	31
1.11.3 8-Channel (7.1) Audio Subsystem	32
1.11.4 6-Channel (5.1) Audio Subsystem	34
1.12 LAN Subsystem	35
1.12.1 Marvell Yukon 88E8050 PCI Express 1.0a Integrated MAC/PHY Gigabit Ethernet Controller	35
1.12.2 RJ-45 LAN Connector with Integrated LEDs	35
1.12.3 Alert Standard Format (ASF) Support	36
1.12.4 LAN Subsystem Software	36
1.13 Hardware Management Subsystem	37
1.13.1 Hardware Monitoring and Fan Control ASIC	37
1.13.2 Thermal Monitoring	38
1.13.3 Fan Monitoring	40
1.13.4 Chassis Intrusion and Detection	40
1.14 Power Management	40
1.14.1 ACPI	40
1.14.2 Hardware Support	43
1.15 Trusted Platform Module (Optional)	47
1.15.1 System Requirements	47
1.15.2 Warning of Potential Data Loss	47
1.15.3 Security Precautions	48
1.15.4 Trusted Platform Module Ownership	49
1.15.5 Enabling the Trusted Platform Module	50
1.15.6 Assuming Trusted Platform Module Ownership	50
1.15.7 Recovery Procedures	51
1.15.8 Clearing Trusted Platform Module Ownership	52
1.15.9 Software Support	53
2 Technical Reference	55
2.1 Introduction	55
2.2 Memory Resources	55
2.2.1 Addressable Memory	55
2.2.2 Memory Map	57
2.3 DMA Channels	57
2.4 Fixed I/O Map	58
2.5 PCI Configuration Space Map	59
2.6 Interrupts	60
2.7 PCI Conventional Interrupt Routing Map	61
2.8 Connectors	63
2.8.1 Back Panel Connectors	63
2.8.2 Component-side Connectors	68
2.9 Jumper Block	80
2.10 Mechanical Considerations	81
2.10.1 D925XECV2 Form Factor	81
2.10.2 D925XEBC2 Form Factor	82
2.10.3 I/O Shield	83
2.11 Electrical Considerations	85
2.11.1 DC Loading	85
2.11.2 Add-in Board Considerations	85
2.11.3 Fan Connector Current Capability	86
2.11.4 Power Supply Considerations	86
2.12 Thermal Considerations	87
2.13 Reliability	89
2.14 Environmental	90
2.15 Regulatory Compliance	91
2.15.1 Safety Regulations	91
2.15.2 EMC Regulations	91
2.15.3 European Union Declaration of Conformity Statement	92
2.15.4 Product Ecology Statements	93
2.15.5 Product Certification Markings (Board Level)	94
3 Overview of BIOS Features	95
3.1 Introduction	95
3.2 BIOS Flash Memory Organization	96
3.3 Resource Configuration	96
3.3.1 PCI Autoconfiguration	96
3.3.2 PCI IDE Support	96
3.4 System Management BIOS (SMBIOS)	97
3.5 Legacy USB Support	97
3.6 BIOS Updates	98
3.6.1 Language Support	98
3.6.2 Custom Splash Screen	98
3.7 Boot Options	99
3.7.1 CD-ROM Boot	99
3.7.2 Network Boot	99
3.7.3 Booting Without Attached Devices	99
3.7.4 Changing the Default Boot Device During POST	99
3.8 Fast Booting Systems with Intel® Rapid BIOS Boot	100
3.8.1 Peripheral Selection and Configuration	100
3.8.2 Intel Rapid BIOS Boot	100
3.9 BIOS Security Features	101
4 Error Messages and Beep Codes	103
4.1 BIOS Error Messages	103
4.2 Port 80h POST Codes	105
4.3 Bus Initialization Checkpoints	109
4.4 Speaker	110