Intel D925XECV2 Product Specification - Page 63

Connectors

Get Intel D925XECV2 PDF manuals and user guides View all Intel D925XECV2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Technical Reference 2.8 Connectors CAUTION Only the following connectors have overcurrent protection: back panel USB, front panel USB, and PS/2. The other internal connectors are not overcurrent protected and should connect only to devices inside the computer's chassis, such as fans and internal peripherals. Do not use these connectors to power devices external to the computer's chassis. A fault in the load presented by the external devices could cause damage to the computer, the power cable, and the external devices themselves. This section describes the board's connectors. The connectors can be divided into these groups: • Back panel I/O connectors • Component-side I/O connectors (see page 68) NOTE When installing the D925XEBC2 board in a microATX chassis, make sure that peripheral devices are installed at least 1.5 inches above the main power connector, the diskette drive connector, the Parallel ATA IDE connector, and the DIMM sockets. 2.8.1 Back Panel Connectors The back panel configuration is dependent upon which audio subsystem is present. The configurations are as follows: • 8-channel (7.1) audio subsystem (five analog audio output connectors and two digital audio output connectors), described on page 64 • 6-channel (5.1) audio subsystem (three analog audio output connectors), described on page 66 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
Technical Reference
63
2.8 Connectors
CAUTION
Only the following connectors have overcurrent protection:
back panel USB, front panel USB, and
PS/2.
The other internal connectors are not overcurrent protected and should connect only to devices
inside the computer’s chassis, such as fans and internal peripherals.
Do not use these connectors
to power devices external to the computer’s chassis.
A fault in the load presented by the external
devices could cause damage to the computer, the power cable, and the external devices themselves.
This section describes the board’s connectors.
The connectors can be divided into these groups:
•
Back panel I/O connectors
•
Component-side I/O connectors (see page 68)
±
NOTE
When installing the D925XEBC2 board in a microATX chassis, make sure that peripheral devices
are installed at least 1.5 inches above the main power connector, the diskette drive connector, the
Parallel ATA IDE connector, and the DIMM sockets.
2.8.1
Back Panel Connectors
The back panel configuration is dependent upon which audio subsystem is present.
The
configurations are as follows:
•
8-channel (7.1) audio subsystem (five analog audio output connectors and two digital audio
output connectors), described on page 64
•
6-channel (5.1) audio subsystem (three analog audio output connectors), described on page 66