Intel SBT2 Product Guide - Page 19

Upgrading, Tools and Supplies Needed, Cautions

Get Intel SBT2 - SS3LE DUAL SLOT2 UPTO 4GB EATX PDF manuals and user guides
UPC - 735858140096
View all Intel SBT2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

2 Upgrading Tools and Supplies Needed • Phillips (cross head) screwdriver (#1 bit and #2 bit) • Jumper removal tool or needle nosed pliers • Pen or pencil • Antistatic wrist strap and conductive foam pad (recommended) Cautions These warnings and cautions apply throughout this chapter. Only a technically qualified person should configure the server board. CAUTIONS System power on/off: The power button DOES NOT turn off the system AC power. To remove power from system, you must unplug the AC power cord from the wall outlet. Make sure the AC power cord is unplugged before you open the chassis, add, or remove any components. Hazardous conditions, devices & cables: Hazardous electrical conditions may be present on power, telephone, and communication cables. Turn off the server and disconnect the power cord, telecommunications systems, networks, and modems attached to the server before opening it. Otherwise, personal injury or equipment damage can result. Electrostatic discharge (ESD) & ESD protection: ESD can damage disk drives, boards, and other parts. We recommend that you perform all procedures in this chapter only at an ESD workstation. If one is not available, provide some ESD protection by wearing an antistatic wrist strap attached to chassis groundany unpainted metal surfaceon your server when handling parts. ESD and handling boards: Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by their edges. After removing a board from its protective wrapper or from the server, place the board component side up on a grounded, static free surface. Use a conductive foam pad if available but not the board wrapper. Do not slide board over any surface. Installing or removing jumpers: A jumper is a small plastic encased conductor that slips over two jumper pins. Some jumpers have a small tab on top that you can grip with your fingertips or with a pair of fine needle nosed pliers. If your jumpers do not have such a tab, take care when using needle nosed pliers to remove or install a jumper; grip the narrow sides of the 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
19
2
Upgrading
Tools and Supplies Needed
•
Phillips (cross head) screwdriver (#1 bit and #2 bit)
•
Jumper removal tool or needle nosed pliers
•
Pen or pencil
•
Antistatic wrist strap and conductive foam pad (recommended)
Cautions
These warnings and cautions apply throughout this chapter.
Only a technically qualified person
should configure the server board.
CAUTIONS
System power on/off:
The power button DOES NOT turn off the system
AC power.
To remove power from system, you must unplug the AC power
cord from the wall outlet.
Make sure the AC power cord is unplugged before
you open the chassis, add, or remove any components.
Hazardous conditions, devices & cables
:
Hazardous electrical
conditions may be present on power, telephone, and communication cables.
Turn off the server and disconnect the power cord, telecommunications
systems, networks, and modems attached to the server before opening it.
Otherwise, personal injury or equipment damage can result.
Electrostatic discharge (ESD) & ESD protection:
ESD can damage
disk drives, boards, and other parts.
We recommend that you perform all
procedures in this chapter only at an ESD workstation.
If one is not
available, provide some ESD protection by wearing an antistatic wrist strap
attached to chassis ground
any unpainted metal surface
on your server
when handling parts.
ESD and handling boards:
Always handle boards carefully.
They can
be extremely sensitive to ESD.
Hold boards only by their edges.
After
removing a board from its protective wrapper or from the server, place the
board component side up on a grounded, static free surface.
Use a
conductive foam pad if available but not the board wrapper.
Do not slide
board over any surface.
Installing or removing jumpers:
A jumper is a small plastic encased
conductor that slips over two jumper pins.
Some jumpers have a small tab on
top that you can grip with your fingertips or with a pair of fine needle nosed
pliers.
If your jumpers do not have such a tab, take care when using needle
nosed pliers to remove or install a jumper; grip the narrow sides of the