Intel SBT2 Product Guide - Page 31

Replacing the Back up Battery, WARNING, ADVARSEL, VAROITUS - ram

Get Intel SBT2 - SS3LE DUAL SLOT2 UPTO 4GB EATX PDF manuals and user guides
UPC - 735858140096
View all Intel SBT2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Replacing the Back up Battery The lithium battery on the server board powers the real time clock (RTC) for up to 10 years in the absence of power. When the battery starts to weaken, it loses voltage, and the server settings stored in CMOS RAM in the RTC (for example, the date and time) may be wrong. Contact your customer service representative or dealer for a list of approved devices. WARNING Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions. ADVARSEL! Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren. ADVARSEL Lithiumbatteri - Eksplosjonsfare. Ved utskifting benyttes kun batteri som anbefalt av apparatfabrikanten. Brukt batteri returneres apparatleverandøren. VARNING Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion. VAROITUS Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. 1. Observe the safety and ESD precautions at the beginning of this chapter. 2. Open the chassis. 3. Insert the tip of a small flat bladed screwdriver, or equivalent, under the tab in the plastic retainer. Gently push down on the screwdriver to lift the battery. 4. Remove the battery from its socket. 5. Dispose of the battery according to local ordinance. 6. Remove the new lithium battery from its package, and, being careful to observe the correct polarity, insert it in the battery socket. 7. Reinstall the plastic retainer on the lithium battery socket. 8. Close the chassis. 9. Run Setup to restore the configuration settings to the RTC. SBT2 Server Board Product Guide 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
SBT2 Server Board Product Guide
31
Replacing the Back up Battery
The lithium battery on the server board powers the real time clock (RTC) for up to 10 years in the
absence of power.
When the battery starts to weaken, it loses voltage, and the server settings stored
in CMOS RAM in the RTC (for example, the date and time) may be wrong.
Contact your customer
service representative or dealer for a list of approved devices.
WARNING
Danger of explosion if battery is incorrectly replaced.
Replace only with
the same or equivalent type recommended by the equipment
manufacturer.
Discard used batteries according to manufacturer’s
instructions.
ADVARSEL
!
Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering.
Udskiftning
må kun ske med batteri af samme fabrikat og type.
Levér det brugte
batteri tilbage til leverandøren.
ADVARSEL
Lithiumbatteri - Eksplosjonsfare.
Ved utskifting benyttes kun batteri
som anbefalt av apparatfabrikanten.
Brukt batteri returneres
apparatleverandøren.
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller
en ekvivalent typ som rekommenderas av apparattillverkaren.
Kassera
använt batteri enligt fabrikantens instruktion.
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu.
Vaihda paristo
ainoastaan laitevalmistajan suosittelemaan tyyppiin.
Hävitä käytetty
paristo valmistajan ohjeiden mukaisesti.
1.
Observe the safety and ESD precautions at the beginning of this chapter.
2.
Open the chassis.
3.
Insert the tip of a small flat bladed screwdriver, or equivalent, under the tab in the plastic
retainer.
Gently push down on the screwdriver to lift the battery.
4.
Remove the battery from its socket.
5.
Dispose of the battery according to local ordinance.
6.
Remove the new lithium battery from its package, and, being careful to observe the correct
polarity, insert it in the battery socket.
7.
Reinstall the plastic retainer on the lithium battery socket.
8.
Close the chassis.
9.
Run Setup to restore the configuration settings to the RTC.